Arduino-info - LCD-Blue-I2C - DATSI

Home » Arduino Lcd I2c Download » Arduino-info - LCD-Blue-I2C - DATSI

Maybe your like

Wikispaces Classroom is now free, social, and easier than ever. Try it today.guest|Únete|Ayuda|Iniciar Sesión
  1. View All Messages
  1. Help Wiki
  • Inicio del wiki
  • Cambios Recientes
  • Pages and Files
  • Miembros
arduino-info
LCD-Blue-I2C Editar 0 81 …
  • 0 Etiquetas
    • No tags
  • Notify
  • RSS
  • Enlaces inversos
  • Source
  • Print
  • Export (PDF)
LCD Displays (Blue and YELLOW) with I2C/TWI Interface YwRobotLCD-4x20-400.jpg

ALL the displays will now use the great Library written by F Malpartida . You should download that Library HERE (Click)

NOTE! THERE ARE THREE (or More??) VERSIONS OF THE 2 and 4 LINE DISPLAYS. Check the small "backpack" interface board on the back. LCD Version 1 - Marked "YwRobot Arduino LCM1602 IIC V1" LCD Version 2 - Marked "Arduino-IIC-LCD GY-LCD-V1" LCD Version 3 - Marked "LCM1602 IIC A0 A1 A2" These displays are Available HERE: NOTE! These displays are very clear bright white on dark blue (or Black on Yellow) background: it is difficult to get a good digital photo due to polarization effects.

WHY THE I2C (IIC) TYPE LCD DISPLAY?

To use this type LCD directly with Arduino, you would need 6 pins: RS, EN, D7, D6, D5, and D4 to talk to the LCD. If you are doing more than a simple project, you may be out of pins using a normal LCD shield. With this I2C interface LCD module, you only need 2 lines (I2C) to display information. If you already have I2C devices in your project, this LCD module actually uses no more pins at all. More information about I2C/TWI (Wikipedia) This unit connects with 4 wires including Vcc and Gnd. It is easiest with a 4-wire cable (supplied) that plugs into the Sensor Shield communications connector. But you can wire it directly yourself if needed: There are 4 pins on the display.. (see photo below) external image 4-pinCable-Pinout-500.jpg

YwRobotLCD-CU-450.jpg

Top to bottom: GND - GND VCC - 5V SDA - ANALOG Pin 4 SCL - ANALOG pin 5 On most Arduino boards, SDA (data line) is on analog input pin 4, and SCL (clock line) is on analog input pin 5. On the Arduino Mega, SDA is digital pin 20 and SCL is 21. NOTE: The Blue Potentiometer (Photo) adjusts Contrast. If you don't see any characters, adjust it. Start clockwise and back down to where the characters are bright and the background does not have boxes behind the characters. See a LCD used in the Temperature-Humidity project.

LiquidCrystal_I2C Library Support Functions

See the "Docs" folder within the Library folder. There are many advanced functions. Below are Example Software Sketches for different displays. They will display characters you type on the Serial Monitor screen on the LCD. NOTE: Line 1 only is correct when writing a long sequence of characters. The characters fill the first line and continue on the third, due to the way the LCD internal addressing works. So this is "normal" and has to do with the LCD hardware. Usually you will set the cursor position before writing characters. (Details in the document linked at the end of this page, if you want them.) (Cut and paste these examples into a blank page on the Arduino IDE). I2C LCD DISPLAY VERSION 1:

Example Software Sketch for 2 line 16 character Displays:

(NOTE: for displays with backpack interface labelled "YwRobot Arduino LCM1602 IIC V1") /* YourDuino.com Example Software Sketch 16 character 2 line I2C Display Backpack Interface labelled "YwRobot Arduino LCM1602 IIC V1" [email protected] */ /*-----( Import needed libraries )-----*/ #include <Wire.h> // Comes with Arduino IDE // Get the LCD I2C Library here: // https://bitbucket.org/fmalpartida/new-liquidcrystal/downloads // Move any other LCD libraries to another folder or delete them // See Library "Docs" folder for possible commands etc. #include <LiquidCrystal_I2C.h> /*-----( Declare Constants )-----*/ /*-----( Declare objects )-----*/ // set the LCD address to 0x27 for a 20 chars 4 line display // Set the pins on the I2C chip used for LCD connections: // addr, en,rw,rs,d4,d5,d6,d7,bl,blpol LiquidCrystal_I2C lcd(0x27, 2, 1, 0, 4, 5, 6, 7, 3, POSITIVE); // Set the LCD I2C address /*-----( Declare Variables )-----*/ //NONE void setup() /*----( SETUP: RUNS ONCE )----*/ { Serial.begin(9600); // Used to type in characters lcd.begin(16,2); // initialize the lcd for 16 chars 2 lines, turn on backlight // ------- Quick 3 blinks of backlight ------------- for(int i = 0; i< 3; i++) { lcd.backlight(); delay(250); lcd.noBacklight(); delay(250); } lcd.backlight(); // finish with backlight on //-------- Write characters on the display ------------------ // NOTE: Cursor Position: (CHAR, LINE) start at 0 lcd.setCursor(0,0); //Start at character 4 on line 0 lcd.print("Hello, world!"); delay(1000); lcd.setCursor(0,1); lcd.print("HI!YourDuino.com"); delay(8000); // Wait and then tell user they can start the Serial Monitor and type in characters to // Display. (Set Serial Monitor option to "No Line Ending") lcd.clear(); lcd.setCursor(0,0); //Start at character 0 on line 0 lcd.print("Use Serial Mon"); lcd.setCursor(0,1); lcd.print("Type to display"); }/*--(end setup )---*/ void loop() /*----( LOOP: RUNS CONSTANTLY )----*/ { { // when characters arrive over the serial port... if (Serial.available()) { // wait a bit for the entire message to arrive delay(100); // clear the screen lcd.clear(); // read all the available characters while (Serial.available() > 0) { // display each character to the LCD lcd.write(Serial.read()); } } } }/* --(end main loop )-- */ /* ( THE END ) */

Example Software Sketch for 4 line 20 character Displays:

(NOTE: for displays with backpack interface labelled "YwRobot Arduino LCM1602 IIC V1") /* YourDuino.com Example Software Sketch 20 character 4 line I2C Display Backpack Interface labelled "YwRobot Arduino LCM1602 IIC V1" Connect Vcc and Ground, SDA to A4, SCL to A5 on Arduino [email protected] */ /*-----( Import needed libraries )-----*/ #include <Wire.h> // Comes with Arduino IDE // Get the LCD I2C Library here: // https://bitbucket.org/fmalpartida/new-liquidcrystal/downloads // Move any other LCD libraries to another folder or delete them // See Library "Docs" folder for possible commands etc. #include <LiquidCrystal_I2C.h> /*-----( Declare Constants )-----*/ /*-----( Declare objects )-----*/ // set the LCD address to 0x27 for a 20 chars 4 line display // Set the pins on the I2C chip used for LCD connections: // addr, en,rw,rs,d4,d5,d6,d7,bl,blpol LiquidCrystal_I2C lcd(0x27, 2, 1, 0, 4, 5, 6, 7, 3, POSITIVE); // Set the LCD I2C address /*-----( Declare Variables )-----*/ void setup() /*----( SETUP: RUNS ONCE )----*/ { Serial.begin(9600); // Used to type in characters lcd.begin(20,4); // initialize the lcd for 20 chars 4 lines, turn on backlight // ------- Quick 3 blinks of backlight ------------- for(int i = 0; i< 3; i++) { lcd.backlight(); delay(250); lcd.noBacklight(); delay(250); } lcd.backlight(); // finish with backlight on //-------- Write characters on the display ------------------ // NOTE: Cursor Position: Lines and Characters start at 0 lcd.setCursor(3,0); //Start at character 4 on line 0 lcd.print("Hello, world!"); delay(1000); lcd.setCursor(2,1); lcd.print("From YourDuino"); delay(1000); lcd.setCursor(0,2); lcd.print("20 by 4 Line Display"); lcd.setCursor(0,3); delay(2000); lcd.print("http://YourDuino.com"); delay(8000); // Wait and then tell user they can start the Serial Monitor and type in characters to // Display. (Set Serial Monitor option to "No Line Ending") lcd.setCursor(0,0); //Start at character 0 on line 0 lcd.print("Start Serial Monitor"); lcd.setCursor(0,1); lcd.print("Type chars 2 display"); }/*--(end setup )---*/ void loop() /*----( LOOP: RUNS CONSTANTLY )----*/ { { // when characters arrive over the serial port... if (Serial.available()) { // wait a bit for the entire message to arrive delay(100); // clear the screen lcd.clear(); // read all the available characters while (Serial.available() > 0) { // display each character to the LCD lcd.write(Serial.read()); } } } }/* --(end main loop )-- */ /* ( THE END ) */ I2C LCD DISPLAY VERSION 2: LCD-Arduino-IIC-LCD-GY-LCD-V1.jpgMarked "Arduino-IIC-LCD GY-LCD-V1" NOTE: The wire connections are in a different order! See the labels on the PC Board.

NEW TYPE 4 line 20 character Displays: Example Software Sketch

/* YourDuino.com Example Software Sketch 20 character 4 line I2C Display Backpack Interface labelled "LCM1602 IIC A0 A1 A2" [email protected] */ /*-----( Import needed libraries )-----*/ #include <Wire.h> // Comes with Arduino IDE // Get the LCD I2C Library here: // https://bitbucket.org/fmalpartida/new-liquidcrystal/downloads // Move any other LCD libraries to another folder or delete them // See Library "Docs" folder for possible commands etc. #include <LiquidCrystal_I2C.h> /*-----( Declare Constants )-----*/ //none /*-----( Declare objects )-----*/ // set the LCD address to 0x27 for a 20 chars 4 line display // Set the pins on the I2C chip used for LCD connections: // addr, en,rw,rs,d4,d5,d6,d7,bl,blpol LiquidCrystal_I2C lcd(0x20, 4, 5, 6, 0, 1, 2, 3, 7, NEGATIVE); // Set the LCD I2C address /*-----( Declare Variables )-----*/ //none void setup() /*----( SETUP: RUNS ONCE )----*/ { Serial.begin(9600); // Used to type in characters lcd.begin(20,4); // initialize the lcd for 20 chars 4 lines // NOTE: Cursor Position: CHAR, LINE) start at 0 lcd.setCursor(3,0); //Start at character 4 on line 0 lcd.print("Hello, world!"); delay(1000); lcd.setCursor(2,1); lcd.print("From YourDuino"); delay(1000); lcd.setCursor(0,2); lcd.print("20 by 4 Line Display"); lcd.setCursor(0,3); delay(2000); lcd.print("http://YourDuino.com"); delay(8000); // Wait and then tell user they can start the Serial Monitor and type in characters to // Display. (Set Serial Monitor option to "No Line Ending") lcd.setCursor(0,0); //Start at character 0 on line 0 lcd.print("Start Serial Monitor"); lcd.setCursor(0,1); lcd.print("Type chars 2 display"); }/*--(end setup )---*/ void loop() /*----( LOOP: RUNS CONSTANTLY )----*/ { { // when characters arrive over the serial port... if (Serial.available()) { // wait a bit for the entire message to arrive delay(100); // clear the screen lcd.clear(); // read all the available characters while (Serial.available() > 0) { // display each character to the LCD lcd.write(Serial.read()); } } } }/* --(end main loop )-- */ /* ( THE END ) */ I2C LCD DISPLAY VERSION 3: This has Yet Another I2C board type marked "LCM1602 IIC A0 A1 A2" (Photo) external image LCD-20x4-New3-800.jpg You need the same new library in the section above. Here's an example Software Sketch that works with this display. Copy this and paste into blank Arduino IDE window. Verify (Need the library above installed), then upload. /* YourDuino.com Example Software Sketch 20 character 4 line I2C Display Backpack Interface labelled "LCM1602 IIC A0 A1 A2" [email protected] */ /*-----( Import needed libraries )-----*/ #include <Wire.h> // Comes with Arduino IDE // Get the LCD I2C Library here: // https://bitbucket.org/fmalpartida/new-liquidcrystal/downloads // Move any other LCD libraries to another folder or delete them // See Library "Docs" folder for possible commands etc. #include <LiquidCrystal_I2C.h> /*-----( Declare Constants )-----*/ //none /*-----( Declare objects )-----*/ // set the LCD address to 0x27 for a 20 chars 4 line display // Set the pins on the I2C chip used for LCD connections: // addr, en,rw,rs,d4,d5,d6,d7,bl,blpol LiquidCrystal_I2C lcd(0x20, 2, 1, 0, 4, 5, 6, 7, 3, POSITIVE); // Set the LCD I2C address /*-----( Declare Variables )-----*/ //none void setup() /*----( SETUP: RUNS ONCE )----*/ { Serial.begin(9600); // Used to type in characters lcd.begin(20,4); // initialize the lcd for 20 chars 4 lines and turn on backlight // ------- Quick 3 blinks of backlight ------------- for(int i = 0; i< 3; i++) { lcd.backlight(); delay(250); lcd.noBacklight(); delay(250); } lcd.backlight(); // finish with backlight on //-------- Write characters on the display ---------------- // NOTE: Cursor Position: CHAR, LINE) start at 0 lcd.setCursor(3,0); //Start at character 4 on line 0 lcd.print("Hello, world!"); delay(1000); lcd.setCursor(2,1); lcd.print("From YourDuino"); delay(1000); lcd.setCursor(0,2); lcd.print("20 by 4 Line Display"); lcd.setCursor(0,3); delay(2000); lcd.print("http://YourDuino.com"); delay(8000); // Wait and then tell user they can start the Serial Monitor and type in characters to // Display. (Set Serial Monitor option to "No Line Ending") lcd.setCursor(0,0); //Start at character 0 on line 0 lcd.print("Start Serial Monitor"); lcd.setCursor(0,1); lcd.print("Type chars 2 display"); }/*--(end setup )---*/ void loop() /*----( LOOP: RUNS CONSTANTLY )----*/ { { // when characters arrive over the serial port... if (Serial.available()) { // wait a bit for the entire message to arrive delay(100); // clear the screen lcd.clear(); // read all the available characters while (Serial.available() > 0) { // display each character to the LCD lcd.write(Serial.read()); } } } }/* --(end main loop )-- */ /* ( THE END ) */ Detailed information about LCD displays from Donald Weiman ([email protected]) LCD Addressing.pdfLCD Addressing.pdf
  • Details
  • Download
  • 251 KB
z

help on how to format text
Página de inicio > ... Cargando... Página de inicio Apagar esta introducción Cargando...

Tag » Arduino Lcd I2c Download