Clean Remote CR2M Series Instructions - ManualsLib

× Bookmark added × Added to my manuals

1. Manuals
2. Brands
3. Clean Remote Manuals
4. Remote Control
5. CR2M Series
6. Instructions

Clean Remote CR2M Series Instructions Hide thumbs 1 2

• page of 2 Go / 2
• Contents
• Table of Contents
• FAQs
• Bookmarks

Advertisement

Table of Contents

• 1 Battery Installation
• 2 No Code Entry/One Step Programming
• 3 For Tv’s Connected to on Command® System Only.
• 4 For Tv’s Connected to Lodgenet® System Only.
• Frequently Asked Questions (8)
• Download this manual

Works over 250 brands of commercial and retail TV's and most Pay-Per-View systems No codes needed for TVs NOT connected to Pay-Per-View Movie systems. Simple ONE TOUCH set-up CLEAN REMOTE® works for TV only (will not work TV/DVD, TV/VCR or TV/DVD/VCR combination units) Hidden Battery compartment and attached door to help prevent batteries from being taken IMPORTANT--- PAY-PER-VIEW MOVIE SYSTEMS DO REQUIRE CODE ENTRY; SEE BACK PAGE batteries

Battery Installation:

1. Open cover: With keypad facing you, first slide dark lens cover away from you (photo A, step 1) and then lift lid upward from the back (photo A, step 2) 2. When placing AAA batteries in the compartment note the + and - symbols on the metal hinge should make contact with the corresponding + and - end of each battery (photo B). 3. Closing cover: With keypad facing away from you gently close cover by pressing downward (photo C, step 1) and sliding it toward the front (keypad) until it is aligned. (photo C, step 2) 4. Test remote by pressing the power button; the LED should light indicating that the batteries are in correctly. If the LED doesn't light, then the batteries are either in wrong or the batteries are bad. Step 2 Photo A Open with keypad facing you For all TV's NOT connected to Pay-Per-View Movie systems 1 . For TV's connected to pay- per - view movie systems turn over page for Instructions. 2. For TV's not connected to pay- per view- movie systems. Turn on the TV and then stand back about 5 feet from TV and point the remote at necessary to point the remote at that exact area once the remote is set-up. 3. Press and firmly hold down the Setup button, do not release. The LED will blink once and then after 7 seconds it will initiate code search. The LED will continue to blink every 2 seconds. Once your TV shuts off immediately remove your finger from the Setup button; the code automatically locks in. 4. Test the remote. If basic functions work, you are done. Menu functions will only work with Pay Per View Systems. Not all buttons will work because this is universal remote. If the main functions are not working properly, you may not have an exact code match. Start again at step #1. The code search will continue where . it left off Important Note: If you think you missed the code or are testing remote on different brand TV's: Reset the remote back to the beginning of the code search; first press and hold the Setup button for 3 seconds and then while still pressing the Setup button down, press and hold the CC button down at the same time until the red LED light blinks quickly 3 times. You have now reset the code list back to the beginning. Go back to step 1. INSTRUCTIONS FOR CR2M * CLEAN REMOTE® Step 1

NO CODE ENTRY/ONE STEP PROGRAMMING

+ - Photo B Close with keypad facing away from you the CENTER of the front panel of the TV. It will not be After Installing 2 AAA Step 1 press down Step 2 Slide in to close Photo C 1 Previous Page Next Page

• 1
• 2

Advertisement

Table of Contents

Frequently Asked Questions (8)

• Why is my Clean Remote CR2M not responding?

  Your Clean Remote CR2M may not be responding for the following reasons:

  • Batteries are incorrect or bad: If the LED doesn't light when you press the power button, the batteries are either installed incorrectly or are bad.
  • Incorrect code match: If the main functions are not working properly after programming, you may not have an exact code match. In this case, you should restart the programming process from step #1.
  • Code not working properly: If a code does not work properly for On Command® or Lodgenet® systems, you should restart the code entry process from the beginning.
  Read more Was this helpful? Yes No
• How do I program my Clean Remote CR2M to my TV?

  The programming method for your Clean Remote CR2M depends on whether your TV is connected to a Pay-Per-View Movie system:

  • For TVs NOT connected to Pay-Per-View Movie systems (One Touch Set-up):

  1. Turn on your TV.

  2. Stand about 5 feet from TV and point the remote at the center of the TV's front panel.

  3. Press and firmly hold down the Setup button. Do not release it. The LED will blink once and then, after 7 seconds, it will initiate a code search, blinking every 2 seconds.

  4. Once your TV shuts off, immediately remove your finger from the Setup button; the code automatically locks in.

  5. Test the remote. If basic functions work, you are done. If main functions are not working properly, you may not have an exact code match, so start again at step #

  6. The code search will continue where it left off.

  • For TVs connected to On Command® system only:

  1. Press the setup and power button together until a solid red light comes on.

  2. Enter code "06". If this doesn't work, try "02". If neither works, try "05, 07, 08, 10" or new codes for cruise ships "14, 15, 16, 17".

  3. The red light should flash twice and go out. If it doesn't, start over.

  4. After putting in the code, make sure you are able to operate standard TV functions such as power, channel, and volume, and fully navigate to Pay-Per-View movies using the menu. If the code does not work properly, start at step A again.

  • For TVs connected to Lodgenet® system only:

  1. On the Clean Remote, press the setup and power button together until a solid red light comes on.

  2. Enter the appropriate code based on your existing Lodgenet® guest room remote:* If your existing Lodgenet® system remote has part number LRC-3200, LRC-3210 or LRC-3220 on the top of the back, enter Code "02". If this doesn't work, try "06".* If your existing Lodgenet® system remote does not have Rewind, Pause, Play or Fast Forward buttons, use Code "11".* If your existing Lodgenet® system remote has Rewind, Play and Fast Forward and # and * symbols, use Code "01".* If the above codes did not work, try "03" or "04".

  3. The red light should flash twice and go out. If it doesn't, start over.

  4. After putting in the code, make sure you are able to operate standard TV functions such as power, channel, and volume, and fully navigate to Pay-Per-View movies using the menu. If the code does not work properly, start at step A again.

  Read more Was this helpful? Yes No
• How do I set up the Clean Remote CR2M as a universal remote?

  The Clean Remote CR2M is designed to work for TVs only and will not work with TV/DVD, TV/VCR, or TV/DVD/VCR combination units. The setup process involves programming it to your TV, which varies depending on whether your TV is connected to a Pay-Per-View Movie system (On Command® or Lodgenet®) or not. After programming, not all buttons will work because it is a universal remote with specific functionalities.

  Read more Was this helpful? Yes No
• How can I reset my Clean Remote CR2M to factory settings?

  To reset the remote back to the beginning of the code search (useful if you think you missed a code or are testing on different brand TVs), follow these steps:

  1. Press and hold the Setup button for 3 seconds.
  2. While still holding the Setup button down, press and hold the CC button down at the same time until the red LED light blinks quickly 3 times. This action resets the code list back to the beginning.
  For more information, see page 1 of the manual. Read more Was this helpful? Yes No
• What type of batteries does the Clean Remote CR2M require?

  The Clean Remote CR2M requires 2 AAA batteries.

  Was this helpful? Yes No
• Is the Clean Remote CR2M compatible with all TV brands?

  The Clean Remote CR2M works over 250 brands of commercial and retail TVs and most Pay-Per-View systems.

  Was this helpful? Yes No
• How do I open the battery compartment of the Clean Remote CR2M?

  To open the battery compartment:

  1. With the keypad facing you, first slide the dark lens cover away from you (as shown in photo A, step 1).
  2. Then, lift the lid upward from the back (as shown in photo A, step 2).
  For more information, see page 1 of the manual. Read more Was this helpful? Yes No
• How do I know if my Clean Remote CR2M is properly programmed?

  After programming, you can verify if your Clean Remote CR2M is properly programmed by:

  • For TVs not connected to Pay-Per-View: Test the remote. If basic functions work, it is properly programmed.
  • For TVs connected to On Command® or Lodgenet® systems: Make sure you are able to operate standard TV functions such as power, channel, and volume. Additionally, you MUST try the menu and ensure you can fully navigate to Pay-Per-View movies.
  Read more Was this helpful? Yes No

Need help?

Do you have a question about the CR2M Series and is the answer not in the manual?

Ask a question

Questions and answers

Related Manuals for Clean Remote CR2M Series

• Remote Control Clean Remote CR2M Instructions (2 pages)
• Remote Control Clean Remote CR2BB Instructions (2 pages)
• Remote Control Clean Remote CR3BCB-H Instructions Multi-bed tv (2 pages)
• Remote Control Clean Remote CR3BCB-H Instructions Clean remote fofotvs (4 pages)

• Remote Control Clean Remote CR3BCB Instructions For (3 pages)
• Remote Control Clean Remote CR1R Instructions (2 pages)
• Remote Control Clean Remote SCR10 Instructions Smart tv remote contro (2 pages)

Summary of Contents for Clean Remote CR2M Series

• Page 1 No codes needed for TVs NOT connected to Pay-Per-View Movie systems. Simple ONE TOUCH set-up CLEAN REMOTE® works for TV only (will not work TV/DVD, TV/VCR or TV/DVD/VCR combination units) Hidden Battery compartment and attached door to help prevent batteries from being taken IMPORTANT--- PAY-PER-VIEW MOVIE SYSTEMS DO REQUIRE CODE ENTRY;...
• Page 2 : PLEASE HAVE YOUR EXISTING REMOTE BEFORE CHOOSING CODE FOR Clean Remote®- Note: Once you find correct code the first time use that same code on the Clean Remote® In all of your guestrooms. A. On The Clean Remote press setup and power button together until solid red light comes on. Next, put in code from list below.

This manual is also suitable for:

Cr2m

Table of Contents

Save PDF

Print

Print page 1 Print document (2 pages)

Rename the bookmark

Cancel

Delete bookmark?

Cancel Delete

Delete from my manuals?

Cancel Delete

Login

Sign In OR Sign in with Facebook Sign in with Google Don't have an account? Sign up! Restore password

Upload manual

Upload from disk Upload from URL Thank you for your help!