ESP8266 NodeMCU PWM With Arduino IDE - Dim LED (Analog ...

This tutorial shows how to generate PWM signals with ESP8266 NodeMCU using Arduino IDE. As an example, we’ll dim the LED brightness by changing the duty cycle over time.

To generate a PWM signal on the ESP8266 pins with Arduino IDE, use analogWrite(pin, value). The value is an integer between 0 and 255.

For ESP8266 releases before 3.0, the default range is between 0 and 1023. The PWM range may be changed by calling analogWriteRange(new_range).

You might also like reading other guides about PWM:

• ESP32 PWM with Arduino IDE – Dim LED
• ESP32/ESP8266 PWM with MicroPython – Dim LED

Before proceeding with this tutorial you should have the ESP8266 add-on installed in your Arduino IDE. Follow the next tutorial to Install ESP8266 in Arduino IDE.

ESP8266 NodeMCU PWM (Pulse-Width Modulation)

The ESP8266 GPIOs can be set either to output 0V or 3.3V, but they can’t output any voltages in between. However, you can output “fake” mid-level voltages using pulse‑width modulation (PWM), which is how you’ll produce varying levels of LED brightness for this project.

If you alternate an LED’s voltage between HIGH and LOW very fast, your eyes can’t keep up with the speed at which the LED switches on and off; you’ll simply see some gradations in brightness.

That’s basically how PWM works — by producing an output that changes between HIGH and LOW at a very high frequency.

The duty cycle is the fraction of the time period at which LED is set to HIGH. The following figure illustrates how PWM works.

A duty cycle of 50 percent results in 50 percent LED brightness, a duty cycle of 0 means the LED is fully off, and a duty cycle of 100 means the LED is fully on. Changing the duty cycle is how you produce different levels of brightness.

analogWrite()

To produce a PWM signal on a given pin you use the following function:

analogWrite(pin, value);

• pin: PWM may be used on pins 0 to 16
• value: should be in range from 0 to PWMRANGE, which is 255 by default. When value is 0, PWM is disable on that pin. A value of 255 corresponds to 100% duty cycle

You can change the PWM range by calling:

analogWriteRange(new_range);

By default, ESP8266 PWM frequency is 1kHz. You can change PWM frequency with:

analogWriteFreq(new_frequency);

Valid values are from 100Hz to 40000Hz.

ESP8266 NodeMCU Dim LED with PWM

In this section, we’ll build a simple example that dims an LED so that you see how to use PWM in your projects. You’ll need the following parts:

• ESP8266 (read Best ESP8266 development boards)
• 5mm LED
• 330 Ohm resistor
• Breadboard
• Jumper wires
• Optional Oscilloscope (read Best Oscilloscopes for Beginners)

If you’re using an ESP-01, you need an FTDI programmer or a Serial Adapter to upload code.

You can use the preceding links or go directly to MakerAdvisor.com/tools to find all the parts for your projects at the best price!

Schematic

After uploading the code, wire an LED to your ESP8266 as shown in the following schematic diagram. We’re connecting the LED to GPIO 2, but you can use any other suitable GPIOs.

If you’re using an ESP-01, you can check the board pinout here.

ESP8266 NodeMCU PWM Code

Copy the code to your Arduino IDE and upload it to your ESP8266.

/********* Rui Santos Complete project details at https://randomnerdtutorials.com *********/ const int ledPin = 2; void setup() { } void loop() { // increase the LED brightness for(int dutyCycle = 0; dutyCycle < 255; dutyCycle++){ // changing the LED brightness with PWM analogWrite(ledPin, dutyCycle); delay(1); } // decrease the LED brightness for(int dutyCycle = 255; dutyCycle > 0; dutyCycle--){ // changing the LED brightness with PWM analogWrite(ledPin, dutyCycle); delay(1); } }

View raw code

How the code works

Continue reading this section to learn how the code works, or skip to the next section.

Start by defining the pin LED is attached to. In this case, LED is attached to GPIO 2 (D4).

const int ledPin = 2;

In the loop(), you vary the duty cycle between 0 and 255 to increase the LED brightness.

for(int dutyCycle = 0; dutyCycle < 255; dutyCycle++){ // changing the LED brightness with PWM analogWrite(ledPin, dutyCycle); delay(1); }

And then, between 255 and 0 to decrease brightness.

for(int dutyCycle = 255; dutyCycle > 0; dutyCycle--){ // changing the LED brightness with PWM analogWrite(ledPin, dutyCycle); delay(1); }

To set the LED brightness, you need to use analogWrite() function that accepts as arguments GPIO where you want to get the PWM signal and a value between 0 and 255 to set the duty cycle.

Upload the Code

In your Arduino IDE, go to Tools > Board and select your ESP8266 model (If you’re using an ESP-01, select “Generic ESP8266 Module”) .

Go to Tools > Port and select the COM port the ESP8266 is connected to.

If you’re using an ESP-01, you need an FTDI programmer or Serial Adapter to upload code. Here are the connections you need to make:

ESP-01	FTDI Programmer
RX	TX
TX	RX
CH_PD	3.3V
GPIO 0	GND
VCC	3.3V
GND	GND

Demonstration

After uploading your sketch, the LED connected to GPIO 2 should increase and decrease its brightness over time.

You can connect GPIO 2 to an oscilloscope to see how the PWM signal changes over time.

Read our buying guide: Best Oscilloscopes for Beginners and Electronics Hobbyists.

Wrapping Up

We hope you’ve found this guide about the ESP8266 PWM usage helpful. Besides controlling the LED brightness, PWM can also be used to control the DC motor’s speed.

You may also like trying our other projects:

• ESP8266 DHT Temperature and Humidity Readings in OLED Display
• ESP8266 DHT Temperature and Humidity Web Server
• Hack a PIR Motion Sensor with an ESP8266
• Build an ESP8266 Web Server

If you like ESP8266 make sure you take a look at our resources:

• Home Automation using ESP8266 (eBook + Video Course)
• Free ESP8266 Tutorials and Projects
• MicroPython Programming with ESP32 and ESP8266

Thanks for reading.