How To Build Simple, Stackable Sawhorses From A Few 2 X 4s

Maybe your like

Newsletter
Pop Mech Pro
Subscribe
Home and DIY
Power Tools
Cars
Technology
Military
Science
Adventure
Sci-Fi
Airplanes
Space
Gifts
Deals
Visual Stories
Promotions
Shop
Follow
My Bookmarks

Skip to Contentsign inSubscribeSearch

sign inSubscribe

Science
Home & DIY
Technology
Gear Reviews
Military
Transportation
Culture & Curiosities
About

My Bookmarks
Newsletter

Privacy NoticeTerms Of Use

sign inSubscribe

Science
Home & DIY
Technology
Gear Reviews
Military
Transportation
Culture & Curiosities
About
More

Wood, Hardwood, Beige, Composite material, Wood stain, Plywood, Idiophone, Lumber, Plank, Fence,

Timothy Dahl

Every workshop needs at least one pair of sawhorses. They can be used as support for holding lumber or painting a door, or, with the help of some plywood, become an instant table. We've highlighted a few popular sawhorse designs including our own, but the following how-to project might be our favorite so far.

This pair of sawhorses requires nothing but 2 x 4s, and the design allows you to stack them conveniently out of the way when not in use. If you don't have enough 2 x 4s in your scrap pile to build this, it will cost less than $20 in wood and screws to buy everything you need.

This style of sawhorse is popular on construction sites everywhere and can be built using nails or screws. We first saw this design used by Mark Clement of My Fix It Up Life and we like the updated version from Jay Bates which allows for clamps to be used on the ends.

We used a miter saw to trim the wood but any saw will do. A measuring tape, pencil, drill/driver, and 3-inch deck screws are the only other tools you'll need for assembly. They shouldn't take longer than an hour to build but they'll last for years. If the top gets cut up or damaged, just replace it with another 2 x 4.

Cut List

Wood, Hardwood, Wooden block, Toy block, Plywood, Lumber,

There are only two lengths of lumber you need for this project. Ten pieces of 30-inch 2 x 4s for the center of the I-beam and the legs, and four pieces of 32-inch 2 x 4s for the top and bottom of the I-beam.

If you are buying new stock, you can cut all of the above from just five pieces of 8-foot 2 x 4s which are available at any Home Depot or Lowe's.

Build the I-Beams

Wood, Hardwood, Composite material, Wood stain, Tool, Lumber, Tool accessory, Glove, Plywood, Workbench,

The I-beam supports the legs and provides a work surface. Stand a 30-inch 2 x 4 on its side and center a longer 32-inch board on top. It should overhang an inch on each end. Drill three pilot holes and attach the pieces using the deck screws. Flip the piece over and repeat the process. The second I-beam should go faster since you've done it before.

Advertisement - Continue Reading Below

Attach the Legs

Wood, Hardwood, Lumber, Plywood, Composite material, Wood stain, Plank,

Angle each 30-inch leg under the lip of the I-beam and drill four pilot holes into the I-beam. Drive four deck screws into each leg to secure them to the sawhorse.

Stack'em Up

Wood, Hardwood, Wood stain, Plywood, Lumber, Plank,

After the legs are attached your sawhorses are ready for use, or just stack them away for storage.

Advertisement - Continue Reading Below

Sawhorse Mods

Tacking carpet onto the top of the sawhorse can prevent your new 'horses from scratching doors, surfboards, or anything else with a fragile finish. You can also paint and seal your sawhorses to finish the look.

Timothy DahlDIY Editor

Timothy is a lifelong DIY enthusiast who is fixated on smart home tech, beautiful tools, and wrenching on his FJ62 Land Cruiser. He’s the DIY editor at Popular Mechanics and also the founder of the home improvement site, Charles & Hudson, the Webby-nominated family site, Built by Kids, and Tool Crave. When not working, you’ll find him on his board or bike enjoying the LA weather with his family and friends. Follow him on Instagram and Twitter.

Watch Next Advertisement - Continue Reading Below