How To: Coat Your 3D Prints With Hydrographics Or Hydro Dip Films ...

Maybe your like

Delivering to - ...

Order History
My Rewards
My Wishlist
Design Library
Account Settings
Logout

Shop

All Tips and Tricks Articles
Getting Started
How To
Women in 3D Printing
Small Business
Healthcare
Weekend Builds
Military & Government
How To Succeed With Any 3D Printing Material
3D Printer Reviews
Reference
MatterControl
Hardware and Upgrades
Education
Creality3D

How to: Coat Your 3D Prints with Hydrographics or Hydro Dip Films

This guide walks through the process of succeeding when using Hydrographics or Hydro Dip Films. Hydrographics is a way of applying complicated graphics and intricate patterns to 3-dimensional objects. The dissolvable hydro dip film is floated on the surface of a tub of water, and the object is literally dipped into it.

Posted on December 18, 2015 by Tyler Anderson (EDIT)

Hydrographics is a process where you overlay a sheet of hydro dip film printed graphics onto an object. The hydrographic dip film is floated on the surface of a tub of water. It dissolves into a layer of paint floating on top the water. When you dip an object into it, the paint conforms and sticks to the surface.

Hydro dip film is sold in many patterns. In this guide we used Carbon Fiber and Brushed Aluminium. Purchase a roll with the pattern of your choice

The hydro dip film process works best with objects that have flat or gently curved surfaces. Pointy and complicated objects do not work as well because the film has trouble wrapping around them. That being said, you may be surprised at the things hydrographics can do.

Hydrographics can only cover half of an object at a time. If you want graphics on all sides, you will need to dip your object multiple times. Beware, though, because the patterns from both sides will not line up.

Plan out how you are going to dip the object before you start. Remember that you will need to hold the object somehow while you are dipping it, and the part you are holding will not get covered.

Tools	Supplies
Scissors or Knife Rubber Gloves Plastic Bin Double Sided Tape	Hydrographic Film Activator Spray Blue Masking Tape A Printed Thing

Step 1 — Cut out a piece of film

Roll out the sheet of film and lay your object on top.
Use scissors or a knife to cut out a piece of the film that is big enough for your object.
Imagine the film is wrapping paper and you are wrapping a birthday present. You need enough film to cover all sides of the object.
Remember that the piece you cut out must still be small enough to fit in your tub of water.
Be careful with the film once you take it out of the bag. If you accidentally get it wet, it will begin to dissolve.

Step 2 — Apply masking tape to film

Now apply strips of masking tape to opposite sides of the film.
The tape will hold the film out while it is floating on the water and prevent it from curling up.
Cut away any excess tape.

Step 3 — Float film on water

Gently float the film on the surface of the water. Put down one edge first and carefully lay down the rest.
If you lay down the entire sheet at once, you will get air bubbles underneath.
Remember to put the shiny smooth side face down and the matte side face up.
After a few seconds, you will see the film wrinkle and then contract.
Let the film soak for 60 seconds before proceeding.

Step 4 — Spray film with activator

If you have no already done so, don your rubber gloves.
After the film has soaked, spray it liberally with the activator.
Cover the film thoroughly using wide strokes.
You will see the film immediately begin to dissolve. Start dipping your object within about 10 seconds
DO NOT BREATH THIS. Always do this outside or in an extremely well ventilated area.

Step 5 — Dip thing

Be careful about where you grab your object. Remember that the part under your fingers will not be coated.
It might be better to stick your fingers to the back of the object using double sided tape, instead.
Slowly dip the object into the water at an angle. Avoid dipping flat surfaces straight in since it can cause air bubbles.
Push the object all the way through the film so that it is completely submerged, then shake it to break off the excess film.
With the object still underwater, use your other hand to clear away the extra bits of film. Then turn the object upside down and pull it back up.

Step 6 — Cleanup

Gently set your object down on some paper towels.
Let it dry for a couple hours before handling.
If you plan to reuse the water for more dipping, clean out as much of the bits of film as you can. A fish net works best for this.
You're done!

Request a Quote

We're open! Call us at +1 (800) 613-4290

To learn about available discounts, training, and maintenance options, please use the form below and a MatterHackers Expert will contact you within one business day. Alternatively, you can always feel free to give us a call at +1 (800) 613-4290 or email [email protected].

Products/Services Estimated Budget * Email * Phone Full Name Company/Organization Questions Interested in Financing options

Tag » How Does Hydro Dipping Work

How To: Coat Your 3D Prints With Hydrographics Or Hydro Dip Films ...

Tools

Supplies

Request a Quote

Article Tags

How To Hydro Dip At Home: Hydro Dipping For Beginners

How Does Hydro Dipping Work? The Science Behind It

Hydro Dipping- What It Is And How It Works - 3D Insider

ELI5:How Does Hydro Dipping Work? : R/explainlikeimfive - Reddit

Complete Process Of Hydrodipping - YouTube

How To Hydro Dip For Beginners - YouTube

Hydro Dip Painting : 12 Steps (with Pictures) - Instructables

Hydro Dipping : 7 Steps - Instructables

Water Transfer Printing - Wikipedia

How Does Hydrographic Dipping Work? The 6-Step Process

How Does Hydrodipping Work And How Much Does It Cost?

How Hydrodraphics & Hydro Dipping Work - CVG FinishTEK

What Is Hydro Dipping Film? - CVG FinishTEK

Hydro Dipping With 2X Rust-Oleum | For The Do-it-yourselfer In You

Contact