How To Edit An STL File Using Segment Editor - 3D Slicer Community Home » How To Edit Stl Files » How To Edit An STL File Using Segment Editor - 3D Slicer Community Maybe your like How To Put On Cpap Mask How To Embed A Quote How To Put On Ear Cuffs How To Put On Hand Wraps How To Embroider A Sweatshirt How to edit an STL file using Segment Editor Support segmentation Hamid (Hamid) May 3, 2021, 8:20pm 1 I want to do some modifications on my stl file. when I open it from file as a data the “Segment Editor” is NOT active. How may I do that? Create a Draw tube and move it lassoan (Andras Lasso) May 11, 2021, 4:54am 2 See step-by-step instructions in Segmentations module documentation (see the tip at the end of the section on how to create a master volume if you don’t have one). 1 Like Hamid (Hamid) May 12, 2021, 3:40am 3 Great! It works now. Thanks a lot. 1 Like Hamid (Hamid) May 14, 2021, 5:54pm 4 I load the stl file and after specifying the geometry I tried to modify the stl file using Draw tube effect. when I click on Draw tube effect a message shows up that says:“change master representation to binary labelmap”. if say YES,the files quality changes like before-after1352×652 76.1 KB attached screenshot. what would be the solution for this? The barbed fitting beforehand is added to the stl file in solidworks.(FYI) Many thanks lassoan (Andras Lasso) May 14, 2021, 6:01pm 5 This is looks good. The resolution you choose determines what details are preserved. If it is not feasible to use a resolution that preserves all the details you need (e.g., because your segmentation is large and your computer could not handle a very fine resolution labelmap of that size) then you can combine image-derived meshes with CAD parts by Boolean mesh operations, using Combine Models module (in Sandbox extension). Hamid (Hamid) May 14, 2021, 7:54pm 6 Thanks for quick reply. This quality does not work for my case because the tube should be fitted to the fitting barbed that you see in the screen shot and this one will end up with a leakage. How may I change the resolution? Does the image spacing change the mentioned quality? for my case the image spacing is 1mm along each axes. What happened if I change it e.g to 0.1mm? lassoan (Andras Lasso) May 14, 2021, 8:49pm 7 Spacing of the binary labelmap representation of the segmentation directly determines “quality”, i.e., size of the smallest details that can be preserved. Typical spacing is between few tenths of a millimeter to a few millimeters - consistent with spacing of the input images. However, if you need fitting between mechanical parts then you would need to work with 1-2 magnitudes smaller spacing along each axis, which would mean that you would have 3-6 magnitudes more voxels in the labelmap. Working with such large labelmaps (tens of GBs in size) is often not practically feasible, so if you need to combine pieces from image-driven segmentations with CAD parts, I would recommend to export the segmentation to models and then combine them with CAD-designed meshes using Combine models module. Hamid (Hamid) December 8, 2021, 6:07pm 8 When I load data (.stl model) into Slicer there are three options(segmentation-model-volume). If I choose model and load it, is there any way to modify the model? e.g cutting a part of it? Thanks mikebind (Mike Bindschadler) December 8, 2021, 6:23pm 9 Look at the Dynamic Modeler module, which provides tools for manipulation of surface models, including cutting. 1 Like Hamid (Hamid) December 10, 2021, 11:11pm 10 Thank you Mike. it works for cutting. Is there any option to fill holes ,…etc there? mikebind (Mike Bindschadler) December 10, 2021, 11:34pm 11 The Surface Toolbox module has a variety of processing options oriented towards cleaning up and optimizing model meshes. One of the options there is “Fill Holes”, which might accomplish what you want (I don’t have experience with using that tool, so I’m not sure how it goes about filling holes). Depending on what manipulations you want to do, you might have an easier time loading your stl as a segmentation and editing it using the Segment Editor tools. Then you can convert back to a surface representation after editing. 1 Like Hamid (Hamid) October 31, 2022, 8:19pm 12 Hello, How can I use painting option with stl file?segment editor is inactive when open a stl file muratmaga (Murat Maga) October 31, 2022, 11:37pm 13 Right click on the stl object in the Data module and choose “convert model to Segmentation node” 1 Like Convert stl to mhd Hamid (Hamid) November 1, 2022, 3:32am 14 Perfect! Thank you so much Muratmaga Related topics Topic Replies Views Activity Convert stl to segmentation and use effect of Segment Editor Support segmentation 1 614 August 3, 2019 PreMade Objets imported from STL files have significant changes when imported as segmentations Support segmentation 5 539 February 13, 2019 STL file import, edit and volume measurment Support segmentation 1 501 September 7, 2021 Import stl object Support 3 860 March 26, 2021 Some loss for convert the stl model to the editable binary labelmap Support segmentation 1 295 June 7, 2021 Tag » How To Edit Stl Files 7 Free STL Editors: How To Edit & Repair STL Files - All3DP The 7 Best Free STL Editors To Edit And Repair Your STL Files Import And Edit STL Files In Fusion 360 2022 - YouTube Editing STL Files THE EASY WAY - YouTube How To Edit/Remix STL Files From Thingiverse – Fusion 360 & More Whats The Best Way To Edit A STL File From Thingiverse? : R/Fusion360 Meshmixer Tutorial: 15 Top Tips To Edit STL Files For 3D Printing Top 10 Best STL Editors Of 2022 - SelfCAD STL Editor 2022: Best Software To Edit And Repair 3D Models Best Free STL Editors 2020 - Top 3D Shop Large STL File Editing Using TinkerCAD - Instructables How To Edit And Modify A STL File For 3D Printing ? 10 Steps To STL ... Edit An STL File In SOLIDWORKS – It's Easier Than You Think How To Edit STL Files In SolidWorks - Quora
