How To Install An Ethernet Jack In A Wall: 14 Steps - WikiHow

Home » How To Run Ethernet Cable Through Walls » How To Install An Ethernet Jack In A Wall: 14 Steps - WikiHow

Maybe your like

Skip to ContentQuizzes
  • Home
  • Random
  • Browse Articles
  • Quizzes & Games
  • All QuizzesHot
  • Love Quizzes
  • Personality Quizzes
  • Fun Games
  • Dating Simulator
  • Learn Something New
  • Forums
  • Courses
  • Happiness Hub
  • Explore More
  • Support wikiHow
  • About wikiHow
  • Log in / Sign up
Terms of Use wikiHow is where trusted research and expert knowledge come together. Learn why people trust wikiHow How to Install an Ethernet Jack in a Wall PDF download Download Article Co-authored by Ricardo Mitchell

Last Updated: February 19, 2026 Fact Checked

PDF download Download Article
  • Creating an Outlet
    • |
  • Running Cable to the Jack
    • |
  • Wiring Your Ethernet Cable
    • |
  • Video
    • |
  • Q&A
    • |
  • Tips
    • |
  • Things You'll Need
|Show more |Show less X

This article was co-authored by Ricardo Mitchell. Ricardo Mitchell is the CEO of CN Coterie, a fully licensed and insured Lead EPA (Environmental Protection Agency) Certified construction company located in Manhattan, New York. CN Coterie specializes in full home renovation, electrical, plumbing, carpentry, cabinetry, furniture restoration, OATH/ECB (Office of Administrative Trials and Hearings/Environmental Control Board) violations removal, and DOB (Department of Buildings) violations removal. Ricardo has over 10 years of electrical and construction experience and his partners have over 30 years of relevant experience. There are 13 references cited in this article, which can be found at the bottom of the page. This article has been fact-checked, ensuring the accuracy of any cited facts and confirming the authority of its sources. This article has been viewed 732,448 times.

If you’re planning on adding a new Ethernet jack to one of the walls in your home, you can save a few bucks by doing it yourself. Installing a network jack is surprisingly easy, and only takes a matter of minutes with the right tools and know-how. Start by identifying a good spot for your jack, taking into consideration the location of your networking hardware and the layout of the rest of the room. Then, trace and cut out a hole for the wall plate that you’ll use to mount the jack itself. After that, it will just be a matter of running the Ethernet cable between the outlet and your modem and wiring the cable to a special connector designed to fit inside the jack.

How to Install an Ethernet Outlet

Trace the outlet's mounting bracket on your wall, and cut the drywall out with a utility knife. Run an Ethernet cable through your wall from your Internet equipment to the new jack. Thread the wires into a keystone connector and attach it to the jack's wall plate.

Steps

Part 1 Part 1 of 3:

Creating an Outlet

PDF download Download Article
  1. Step 1 Choose a convenient location for your Ethernet jack. 1 Choose a convenient location for your Ethernet jack. Scan the room for an open spot down low on the wall, preferably near an electrical outlet. Use an electronic stud finder to determine the exact location of the stud closest to the outlet. You can either put your Ethernet jack on the opposite side of this stud or on either side of the next stud in the row.[1]
    • Ideally, the location you select should be free from surrounding obstructions and provide a clear path to run your Ethernet cable later on.
    • Most Internet installers recommend setting up a new network jack a few inches from an existing outlet to establish a sense of symmetry and limit the number of potentially-unattractive wiring fixtures on other parts of the wall.

    Tip: When determining the best location for your jack, consider where the network hardware furnished by your internet service provider is stationed in your home. You’ll want to situate your jack as close to this spot as possible in order to simplify the process of running and connecting your Ethernet cable.

  2. 2 Mark the spot on the wall where you want to place the jack. Use a pencil to draw a small ‘X’ where the jack will go. Don’t obsess over the placement too much—you’ll be able to make any necessary adjustments when marking the exact location of the mounting bracket.
    • Make your mark dark enough to be plainly visible so you won't have to hunt for it while you're doing other things.
    Advertisement
  3. Step 3 Place your mounting bracket over the marking and trace around the inside. 3 Place your mounting bracket over the marking and trace around the inside. Once you’ve got the bracket situated right where you want it, run the tip of your pencil along the inner edge of the wall plate mounting bracket for your network jack. When you’re done, you’ll have a rough outline that you can use as a template for cutting the hole for the wall plate.
    • Line the wall mounting bracket up as evenly as you can with the nearby electrical outlet.
    • If desired, use a bubble level to ensure that the top and bottom edges of your outline are perfectly parallel with the floor.
  4. Step 4 Shut off the electricity to any electrical circuits in the immediate vicinity. 4 Shut off the electricity to any electrical circuits in the immediate vicinity. Head to the main circuit breaker panel or electrical control box for your building and flip the switch corresponding to the outlet you’ve chosen to install your network jack next to. Doing so will minimize your risk of electrical shock, as you’ll be working close by.
    • Individual circuits should be plainly labelled on your breaker panel.
    • If you’re attempting to install an Ethernet jack somewhere other than your own home, you may need some assistance finding the right breaker.
    • If for some reason your breakers aren’t labelled, or they’ve been labelled incorrectly by mistake, an electronic circuit breaker finder can help you figure out which breaker to flip.
  5. Step 5 Cut around the outline you just drew using a utility knife. 5 Cut around the outline you just drew using a utility knife. Score the outline lightly to make sure your lines are neat and precise. Then, go back over each line multiple times, applying more pressure each time. After a few passes, the excess drywall will simply pop out and you’ll be left with a nice clean hole for your Ethernet jack’s wall plate.[2]
    • You can also cut out the outline for your wall plate using a drywall saw, if you prefer.
    • Be careful not to make the hole too big. If you cut it too small, you can always go back and enlarge it, but if it ends up being larger than the mounting bracket for the wall plate, you’ll be out of luck.
    6. Advertisement
Part 2 Part 2 of 3:

Running Cable to the Jack

PDF download Download Article
  1. 1 Drill a hole in the floor or ceiling behind your jack outlet if necessary. Depending on where your Internet equipment is located, you may need to run your Ethernet cable either up or down a level to its termination point. Fit a power drill with a 1⁄2 in (1.3 cm) drill bit and bore a hole directly above or below the outlet opening you just cut behind the wall. This will make it possible to route the cable from your networking hardware to the new jack.[3]
    • In most cases, the hardware setup that provides wired access to the Internet will be found in the attic, basement, or crawl space beneath your home.
  2. Step 2 Run your Ethernet cable from your networking hardware to the jack outlet. 2 Run your Ethernet cable from your networking hardware to the jack outlet. If you’ve drilled through the floor to reach your Internet equipment, feed the cable through the outlet opening and down into the lower level. If you’ve drilled up through the ceiling, it will make more sense to start at your networking center and guide the cable down a level to the location of the jack. In other words, always work from top to bottom.[4]
    • Avoid running the cable too close to electrical lines, water pipes, or other fixtures hidden behind your walls or beneath your floor. If for some reason you have no choice but to cross an electrical line, do it perpendicularly at a single point to reduce potential electrical interference.

    Tip: If you’re planning on hooking more than one Ethernet cable up to your network jack, wrap a strip of tape around the ends of the cables to keep them together as you snake them through the wall.[5]

  3. Step 3 Secure the mounting bracket for your wall plate in the wall. 3 Secure the mounting bracket for your wall plate in the wall. After threading the slack end of your Ethernet cable through the middle, insert the rectangular plastic bracket into the opening you cut out earlier. Fasten the bracket by drilling the included installation screws directly into the drywall through the molded holes at the top and bottom corners.[6]
    • Avoid overtightening the installation screws, as this could cause visible cracks in the drywall around the finished wall plate.
  4. Step 4 Cut the cable emerging from the outlet to a length of 6–12 inches (15–30 cm). 4 Cut the cable emerging from the outlet to a length of 6–12 inches (15–30 cm). Use a pair of wire cutters to snip off the excess cabling. Aim for a clean, 90-degree cut straight across the cable’s width, and be sure to leave around 1⁄2–1 ft (15–30 cm) of cabling hanging out of the outlet to ensure a comfortable fit and prevent unnecessary pull.[7]
    • If you cut the cable too short, the resulting tension could damage the internal wiring or cause the entire cable to pull loose of the jack over time.
    5. Advertisement
Part 3 Part 3 of 3:

Wiring Your Ethernet Cable

PDF download Download Article
  1. Step 1 Strip the outer sheathing from the last 2 inches (5.1 cm) of cable. 1 Strip the outer sheathing from the last 2 inches (5.1 cm) of cable. Place the cable inside a wire stripper in the appropriate notch for its gauge size.[8] Squeeze the handles of the tool to clamp the jaws down around the cable and cut through the sheathing, then slide off the loose sheathing while holding the cable steady.[9]
    • You should be able to find the exact gauge of your Ethernet cable listed somewhere on the package.
    • If you don’t have a cable stripper, you can also slice through the cable covering using a utility knife or pair of scissors. Just be careful not to sever or otherwise damage any of the wires themselves.[10]
  2. Step 2 Thread the exposed wires into the color-coded slots on the keystone connector. 2 Thread the exposed wires into the color-coded slots on the keystone connector. Most Ethernet cables contain 4 pairs of similarly colored wires. Untwist each pair to separate the individual wires, then fan them out to bring them closer to their respective slots. Align each wire with its corresponding slot and slip it down inside.[11]
    • Keep in mind that you’ll need to do this for the end of the cable leading to your modem, as well.
    • If you want to make things a lot easier on yourself, pick up a pre-connectorized Ethernet cable. This type of cable already comes fitted with the keystone connector ends designed to fit into your new jack, making it possible to simply plug-and-play.[12]

    Tip: There are two standard configurations for wiring Ethernet cables: T568A and T568B. The layout of the wires is a little different in each of the two standards, but you can use either one as long as your wire both ends of the cable using the same standard.[13]

  3. Step 3 Force the wires down into their respective slots using a 110 punch-down tool. 3 Force the wires down into their respective slots using a 110 punch-down tool. Align the pointed end of the tool with the top of the first slot and push straight down. As you do, the forked prongs will seat the wire snugly at the bottom of the slot, which will in turn slice through sheathing to enable conductivity. Repeat this action for each of the 7 remaining wires.[14]
    • Many newer punch-down tools also clip the excess wire at the edge of each slot automatically. If yours doesn’t, just grab your wire cutters and trim them as close to the connector as possible.
    • It may help to use a punch-down puck to brace the keystone connector as you work. A punch-down puck is a type of stabilizer base that holds small connector heads in place during crimping.
  4. Step 4 Plug the wired connector head into the backside of the wall plate. 4 Plug the wired connector head into the backside of the wall plate. If your keystone connector came with protective cover plates, snap them into place on the top or bottom of the connector head. Then, insert the connector into the wall plate on the side facing the interior of the wall. You’ll hear a click letting you know that the connection is secure.[15]
    • Be sure to buy a cover designed specifically for a keystone connectors. Otherwise, your cable won’t fit.
    • If you like, you can use a cable tester to confirm that your Ethernet cable and keystone connector are wired properly before moving on. That way, you won’t have to disassemble the outlet later on if you experience connectivity issues.[16]
  5. 5 Fasten the wall plate over the jack mounting bracket to complete installation. Slip the included installation screws into the holes at the top and bottom of the wall plate. Use a power drill or screwdriver to tighten them inside the corresponding holes in the mounting bracket. Give the wall plate a quick jostle to make sure it’s secure, then connect to your computer or router to get online.[17]
    • Don’t forget to vacuum up any loose drywall or other debris that’s found its way onto the floor in front of the outlet.
    6. Advertisement

Community Q&A

Search Add New Question
  • Question Do I strip the small wires before connecting to the jack? Community Answer Community Answer No, neither for patch cable nor for installation cable. Don't strip small wires. Just strip the whole cable as needed for the type of the socket or connector you're going to mount. Thanks! We're glad this was helpful. Thank you for your feedback. If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow Yes No Not Helpful 6 Helpful 27
  • Question About how much does this project cost? CurtM CurtM Community Answer You can install a new Ethernet jack for around $150-300 USD, or even less, if you already own some of the necessary tools and equipment. Thanks! We're glad this was helpful. Thank you for your feedback. If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow Yes No Not Helpful 146 Helpful 13
  • Question Is it possible to do this without cutting open the wire? Couldn't I just run a standard ethernet cable through the walls and into my PC? Community Answer Community Answer Yes, and to finish the wall nicely, use a "flexible opening cable wall plate", a "brush plate", or a "recessed cable plate". Thanks! We're glad this was helpful. Thank you for your feedback. If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow Yes No Not Helpful 6 Helpful 38
Ask a Question 200 characters left Include your email address to get a message when this question is answered. Submit Advertisement

Video

Tips

  • If you’re not confident in your ability to set up a new network jack correctly, your best bet is to hire a qualified Internet installation service to make sure the job gets done right. The added cost will be worth it to spare yourself the headache and possible unnecessary damage to your home. Thanks Helpful 3 Not Helpful 0
  • Pick out the highest quality Ethernet cable that your budget allows to make sure it’s capable of handling more data as Internet speeds continue to improve in the future. Thanks Helpful 6 Not Helpful 2
Submit a Tip All tip submissions are carefully reviewed before being published Name Please provide your name and last initial Submit Thanks for submitting a tip for review! Advertisement

Things You’ll Need

Positioning the Jack

  • Pencil
  • Wall plate mounting bracket
  • Electronic stud finder (optional)
  • Bubble level (optional)
  • Electronic circuit breaker finder (optional)

Running Cable to the Jack

  • Utility knife
  • Power drill
  • 1⁄2 in (1.3 cm) drill bit
  • Ethernet cable
  • Wire cutters
  • Drywall saw (optional)
  • Tape (optional)

Wiring Your Ethernet Cable

  • Wire stripper
  • Keystone connector head
  • 110 punch-down tool
  • Power drill or screwdriver
  • Utility knife or scissors (optional)
  • Punch-down puck (optional)
  • Cable tester (optional)

You Might Also Like

Add an Electrical Outlet to a WallHow toAdd an Electrical Outlet to a Wall Install Cabling in a Pre Built HomeHow toInstall Cabling in a Pre Built Home Install a Residential Telephone JackHow to Hook Up Telephone Jack Yourself Wire a 220V OutletHow to Wire a 220V Outlet: A Step-by-Step Guide Wire a Simple 120v Electrical CircuitHow toWire a Simple 120v Electrical Circuit Fish Wires Through WallsHow to Run Electrical Wires through Finished Walls Make a Network CableHow toMake a Network Cable Install a ModemHow toInstall a Modem Install an Outdoor OutletHow toInstall an Outdoor Outlet Wire an Ethernet CableHow toWire an Ethernet Cable Install a Flat Panel TV on a Wall With No Wires ShowingHow toInstall a Flat Panel TV on a Wall With No Wires Showing Install Cable TelevisionHow toInstall Cable Television Create an Ethernet CableHow toCreate an Ethernet Cable Make an RJ‐45 CableHow toMake an RJ‐45 Cable Advertisement

References

  1. ↑ https://www.pcworld.com/article/503325/wire_your_home_for_ethernet.html
  2. ↑ https://www.familyhandyman.com/project/how-to-cut-drywall-for-an-opening/
  3. ↑ https://www.familyhandyman.com/project/add-electrical-outlet/
  4. ↑ https://www.cnet.com/home/internet/home-networking-explained-part-2-optimizing-your-wi-fi-network/
  5. ↑ https://www.youtube.com/watch?v=chsZZh-dZRw&feature=youtu.be&t=268
  6. ↑ https://www.youtube.com/watch?v=chsZZh-dZRw&feature=youtu.be&t=343
  7. ↑ https://www.pcworld.com/article/503325/wire_your_home_for_ethernet.html
  8. ↑ Ricardo Mitchell. Electrician & Construction Professional, CN Coterie. Expert Interview
  9. ↑ https://www.familyhandyman.com/project/add-electrical-outlet/
More References (8)
  1. ↑ https://www.angi.com/articles/how-to-strip-wire.htm
  2. ↑ https://www.youtube.com/watch?v=chsZZh-dZRw&feature=youtu.be&t=418
  3. ↑ https://www.tpcwire.com/blog/the-dos-donts-of-installing-ethernet-cable
  4. ↑ https://www.cnet.com/culture/how-to-make-your-own-ethernet-cable/
  5. ↑ https://www.pcworld.com/article/503325/wire_your_home_for_ethernet.html
  6. ↑ https://www.youtube.com/watch?v=chsZZh-dZRw&feature=youtu.be&t=447
  7. ↑ https://www.cnet.com/culture/how-to-make-your-own-ethernet-cable/
  8. ↑ https://www.youtube.com/watch?v=OutfS8wYdA0&feature=youtu.be&t=1113

About This Article

Ricardo Mitchell Co-authored by: Ricardo Mitchell Electrician & Construction Professional, CN Coterie This article was co-authored by Ricardo Mitchell. Ricardo Mitchell is the CEO of CN Coterie, a fully licensed and insured Lead EPA (Environmental Protection Agency) Certified construction company located in Manhattan, New York. CN Coterie specializes in full home renovation, electrical, plumbing, carpentry, cabinetry, furniture restoration, OATH/ECB (Office of Administrative Trials and Hearings/Environmental Control Board) violations removal, and DOB (Department of Buildings) violations removal. Ricardo has over 10 years of electrical and construction experience and his partners have over 30 years of relevant experience. This article has been viewed 732,448 times. How helpful is this? Co-authors: 12 Updated: February 19, 2026 Views: 732,448 Categories: Networking Hardware In other languages French German Hindi Spanish Czech Japanese
  • Print
  • Send fan mail to authors
Thanks to all authors for creating a page that has been read 732,448 times.

Is this article up to date?

Yes No Advertisement Cookies make wikiHow better. By continuing to use our site, you agree to our cookie policy. Ricardo Mitchell Co-authored by: Ricardo Mitchell Electrician & Construction Professional, CN Coterie Click a star to vote Co-authors: 12 Updated: February 19, 2026 Views: 732,448

Quizzes & Games

Finish the Phrase QuizFinish the Phrase QuizTake QuizAm I Good at Flirting QuizAm I Good at Flirting QuizTake QuizDo I Have Common Sense QuizDo I Have Common Sense QuizTake QuizAm I Smart QuizAm I Smart QuizTake Quiz

You Might Also Like

Add an Electrical Outlet to a WallHow toAdd an Electrical Outlet to a WallInstall Cabling in a Pre Built HomeHow toInstall Cabling in a Pre Built HomeInstall a Residential Telephone JackHow to Hook Up Telephone Jack YourselfWire a 220V OutletHow to Wire a 220V Outlet: A Step-by-Step Guide

Trending Articles

Psychopath TestPsychopath TestWhat Female Body Shape Are You? How to Identify YoursWhat Female Body Shape Are You? How to Identify YoursWhat Kind of Cat Am I QuizWhat Kind of Cat Am I QuizIf I Were A... QuizIf I Were A... Quiz

Trending Articles

Do You Agree with These "Hear Me Out" Character Hot Takes?Do You Agree with These "Hear Me Out" Character Hot Takes?Do I Have Main Character Energy?Do I Have Main Character Energy?Can Your Finger Length Tell Your Personality?Can Your Finger Length Tell Your Personality?What Are Narrow Clavicles? Plus, How to Build Shoulder Width with ExercisesWhat Are Narrow Clavicles? Plus, How to Build Shoulder Width with Exercises

Take the Quiz Everyone Is Talking About

Am I Gay QuizAm I Gay QuizWhat Animal Am I QuizWhat Animal Am I QuizWhat Is My Mental Age QuizWhat Is My Mental Age QuizHow Well Do I Know My Best Friend QuizHow Well Do I Know My Best Friend Quiz

You've Seen These All Over Your Feed

10+ Scary Phone Numbers to Call10+ Scary Phone Numbers to Call360 of the Best Borg Names for Your Next Party: Unique, Historical & More360 of the Best Borg Names for Your Next Party: Unique, Historical & MoreWhat Every Domain Expansion Hand Sign Means In Jujutsu KaisenWhat Every Domain Expansion Hand Sign Means In Jujutsu KaisenThe Ultimate List of Truth or Drink QuestionsThe Ultimate List of Truth or Drink Questions

Featured Videos

Play Dice (2 Dice Gambling Games)How toPlay Dice (2 Dice Gambling Games)Persuade a Girl over TextHow toPersuade a Girl over TextGive Someone the Silent TreatmentHow toGive Someone the Silent TreatmentMake Hibiscus TeaHow toMake Hibiscus Tea

Hot Takes 🔥 🔥 🔥

Do You Agree with These Crazy Hot Takes?Do You Agree with These Crazy Hot Takes?Do You Agree with These Pop Culture Hot Takes?Do You Agree with These Pop Culture Hot Takes?Do You Agree With These Fashion Hot Takes?Do You Agree With These Fashion Hot Takes?Do You Agree With These Board Game Hot Takes?Do You Agree With These Board Game Hot Takes?

Your Daily Dose of Fun!

When Will I Get My First Period QuizWhen Will I Get My First Period QuizAm I a Bruh Girl?Am I a Bruh Girl?Which My Little Pony Am I QuizWhich My Little Pony Am I QuizAm I Cool QuizAm I Cool Quiz wikiHow
  • Categories
  • Computers and Electronics
  • Computer Networking
  • Networking Hardware
wikiHow Newsletter You're all set! Helpful how-tos delivered toyour inbox every week! Sign me up! By signing up you are agreeing to receive emails according to our privacy policy.
  • Home
  • About wikiHow
  • Experts
  • Jobs
  • Contact Us
  • Site Map
  • Terms of Use
  • Privacy Policy
  • Do Not Sell or Share My Info
  • Not Selling Info
  • Contribute

Follow Us

×

wikiHow Tech Help:

Tech troubles got you down? We've got the tips you need

Subscribe You're all set! X --497

Tag » How To Run Ethernet Cable Through Walls