How To Lay A Gravel Driveway - Ultimate DIY Guide

[Ad – This post is in collaboration with MatsGrids and contains affiliate links. We only recommend products we love and think that you will, too! Read our full disclaimer here. ]

After working on it on and off for months, we have finally finished installing our gravel driveway!

We love how it turned out, and although it’s taken us almost a year to complete, it isn’t difficult to lay a gravel driveway or even that much work to do!

Most projects we take on tend to take longer than we think, be more involved than we imagined and cost more than we expect. However, laying a gravel driveway turned out to be much easier than we’d anticipated (although it was hard work at times).

Here’s our guide on how to lay a gravel driveway

Step 1Prepare The Driveway (Aka. The hard work and dirty bit)

Like most of our garden, the driveway used to be covered in tarmac that had seen better days. So, before we could even begin to think about laying a gravel driveway, we inevitably had to get out our shovels and get digging.

Removing the first layer of already broken tarmac turned out to be easy and fairly quick, but removing the rest of the surface was a miserable experience.

There should have really been a firm foundation layer under the tarmac, but it turned out to be more of a mixture of clay, soil and rubble. Not exactly ideal if you consider that it’s meant to be there to support the weight of cars.

A lot of digging and two full skips later, the driveway was finally tarmac and dirt-free (this is the part of the project that took by far the longest to complete), and we could finally order some more rubble to replace the rubble we’d just removed.

No time to read now?

No worries! Save on Pinterest to read it later.

Step 2Add The Driveway Base Layer

It felt so mad to pay for skip loads of rubble to be removed only to end up paying for new rubble to be delivered, but the base of the driveway is really important, and the quality of the aggregate you use has to be right.

For driveway subbases, you should be using MOT Type 1, which consists of different-sized pieces of aggregate that compact together to form a solid base that’s suitable for heavier loads.

At first, we calculated that two bulk bags of MOT would be enough to cover our driveway. However, it wasn’t even close, so we had to order two more bags, which still turned out not to be quite enough, and we ended up having to order a fifth bag to reach the height we needed.

Needless to say not one of our best DIY planning moments, but we got there in the end and after a few hours of shovelling and levelling out the base layer (it has to slope away from the garage) it was finally time to get out the wacker!

Yes, the wacker! We may own more than a few power tools, but unsurprisingly, a wacker isn’t one of them.

Luckily, we were able to borrow one from one of our lovely neighbours, who happens to be a builder and was kind enough to give me a hand getting things started.

I’ll totally admit that I was more than just a bit apprehensive about using the wacker, but actually, I shouldn’t have worried too much.

Yes, it was really dusty, heavy, and noisy, but it was easy to use and compacted the whole driveway in about 15 minutes.

As so often, the prep work turned out to be the most time-consuming part of this project, and the next steps were really quick.

We forgot to add the layer of weed control membrane under the MOT, so we decided to install it on top of it instead. When I say install, I actually mean spend 5 minutes rolling it out.

Then it was time to get shovelling. Again. Yep, we really know how to have fun around here! This time, we had to add a layer of sand over the MOT and weed membrane.

Jan was working away the week that the sand was delivered, so I had to shovel almost a ton of sand myself in preparation for the gravel that was due to get delivered later that same week.

Not exactly great timing or the most fun afternoon ever, but it was weirdly exciting to see more progress, and the finishing line was definitely in sight!

Step 3Add The Gravel Grids

Although we knew we wanted a gravel driveway, we were concerned about ending up with gravel everywhere or an uneven surface every time we drove or walked across it. This is why we opted to install gravel grids.

Basically, they are mats with little pockets that get filled with gravel, which keeps your gravel in position and the driveway looking great. We used these gravel grids by MatsGrids.

Adding the gravel grids to the driveway was easily my favourite part of this project. It was so quick to do (I laid them on my own), and it is probably one of the easiest DIY jobs we’ve ever done.

It is important that the sand is level (I used an offcut of timber to level and smooth it as I worked my way from one end of the driveway to the other) because it could otherwise be difficult to get the mats to lock together, but I had absolutely no problems at all and everything just slotted into place – literally.

There are little hooks on the edges of the mats, and they just all lock into each other.

Even cutting them turned out to be surprisingly easy. I had thought I might need an angle grinder or something else heavy-duty to cut them, but all I used was a standard fine saw.

It only took me 1.5 hours to cover the whole driveway, which is probably why I enjoyed this step so much (yep, you could call me impatient).

Don’t Miss: How to Lay a Gravel Path: No-Nonsense DIY Guide

Step 4Add The Gravel

Laying a gravel driveway really wouldn’t be complete without actually laying gravel, would it?

We followed the advice of MatGrids for the gravel (they recommend angular gravel up to 20mm for their grids) and decided to choose Dove Grey Limestone gravel.

It’s a soft light grey colour, and it seemed perfect as we wanted something light and modern looking that would contrast nicely with the dark fence.

Like the MOT and sharp sand, it came in big bulk bags (we used three bags – about 1.5 for the actual driveway and the rest for the area along the wall).

If you’d not already guessed, I was well and truly sick of shovelling by this point, but with the project so near to completion and Jan back home to help, it only took a few more hours (with a few breaks because of torrential rain) and we finally finished laying our gravel driveway!

Materials & cost breakdown (to lay a gravel driveway that’s about 15m²):

• MOT Type 1 £200
• Sharp Sand £40
• Weed Control Membrane £20
• Gravel Mats £225 (ours were kindly supplied by MatsGrids)
• Gravel £160
• Total gravel driveway cost: £665

We love how the driveway has turned out, and as you can probably tell, there was nothing difficult about this project at all. Jan did most of the shovelling, and I did most of putting things back together again.

Because this project has happened over such a long time, it’s difficult to remember just how far we’ve come, so here are the obligatory before and after pictures.

My biggest concern about laying a gravel driveway was that it would end up looking untidy, but so far the gravel hasn’t moved, and it’s still really tidy and level.

Do you also find that projects seem to take longer and cost more than anticipated? Have you ever had a project that turned out to be easier than expected?

SHOP OUR DIY ESSENTIALS

If you like this project, you will love these other outdoor projects!