How To Lay Sheet Vinyl | Flooring & Tiling - B&Q

Home » How To Lay Vinyl Sheet Flooring » How To Lay Sheet Vinyl | Flooring & Tiling - B&Q

Maybe your like

Skip to content
  • B&Q Club
  • Customer support
  • Sell on diy.com
  • B&Q Club
  • Customer support
  • Sell on diy.com
Click + Collect now in as little as 15 minutes*
*Restrictions apply
Free delivery on 1000s of products
Selected products/locations
90 day returns policy
Join B&Q Club
Save up to £100 a year▲
 See more Vinyl flooring
  1. Home
  2. Ideas & Advice
  3. Flooring & Tiling
  4. Vinyl flooring

  5. How to lay sheet vinyl

How to lay sheet vinyl

  • Sheet vinyl is an affordable and easy to install alternative to other flooring types. In this guide, we show you how you can lay your own sheet vinyl.

    Jump to:

    • How to lay sheet vinyl floor
    • Securing vinyl to the floor
    • Fitting around toilets & basins
    • Fitting around pipes
    • Fitting around door frames
    • Fitting at external corners
    • Joining two sheets together
  • Shop Sheet VinylShop Sheet Vinyl

How to lay sheet vinyl flooring

Before laying your floor, you can work out how much sheet vinyl you'll need by calculating the area of the room and adding 50mm-100mm to each edge. Don't forget to measure right into any alcoves and up to the half-way point in the doorway.

Keep your roll of vinyl for 48 hours in the room where you'll be laying it, as this brings it up to room temperature. When laying your flooring, wear protective knee pads.

Block of wood with a nail hammered in it pushed up against skirting board on top of vinyl sheet.

1. Fit against the longest clear wall

Start by unrolling your vinyl and fitting the longer side of the sheet parallel to the longest clear wall, about 25mm away from the skirting.

Skirting is not often completely straight, and you'll need to trace its profile onto your vinyl before you cut it to fit the longest clear wall. You can use a home-made tool known as a scribing gauge to do this. To make a scribing gauge, take an off-cut of wood and hammer a nail into it about 30mm from one end until the point is just sticking out of the other side.

Carefully move your scribing gauge along the skirting so the nail traces the outline of the skirting onto the vinyl. Then, cut the sheet along this line with a knife or scissors, and slide the vinyl against the skirting.

Using a pair of scissors to cut a triangular notch out of the corner of a vinyl sheet.

2. Cut the corners

To get the vinyl to lie as flat as possible, you'll need to cut a triangular notch at each internal corner with scissors. The cut is made in the extra allowed along each wall.

Using a bolster chisel to push vinyl flooring into the gap between a skirting board and floor.

3. Push the vinyl against the skirting

Press the vinyl into the angle between the skirting and floor with a bolster chisel to make a sharp crease.

Holding a metal ruler against a crease in vinyl flooring between the floor and skirting board. Knife is being run along the side of a ruler to cut the vinyl in a straight line.

4. Trim the vinyl

Hold a metal straightedge against the crease and cut carefully along it with a utility knife held at a slight angle.

Corner of sheet vinyl flooring has been lifted and is being sprayed with vinyl floor adhesive using a spray can.

5. Secure to the floor

Not all vinyl has to be glued to the floor. Heavy duty 'stay flat' vinyl doesn't shrink or lift, so you can lay it without using adhesive.

If you're laying cushioned vinyl, you should glue it around the edges and at joins. Thinner, non-cushioned types need to be stuck down all over.

Once you've fitted your vinyl, roll half of it back and apply adhesive to the floor (using the type that's supplied or recommended by the manufacturer). Re-position the vinyl and repeat the process for the other half of your room. When it's all back in place, press the vinyl flat with a soft broom.

It's always a good idea to apply silicone sealant to the edges of your bathroom floor to create a waterproof barrier.

Fitting vinyl around toilets and basins

Sheet vinyl laid around the base of a toilet. Vertical cuts have been made in the vinyl around the toilet to allow it to be pushed around the toilet using a chisel.

To fit vinyl around your toilet or wash basin pedestal, you'll need to lay it as far as the front of the pedestal, then fold it back on itself. Use scissors to cut in from the edge in a straight line to the centre of the pedestal.

Next, make a series of cuts in the vinyl around the base of the pedestal or toilet until the sheet lies flat. Be careful not to cut too far in, or tear the vinyl.

Use a bolster chisel to make a sharp crease in the vinyl all the way round the base of the pedestal.

Using a utility knife to trim a piece of excess vinyl floor around the base of a toilet.

Cut around the crease you've made and carefully trim off each flap of vinyl until it fits. Next, peel back the vinyl, put adhesive on the floor around the pedestal and press it back into place. You can seal the edges with silicone sealant if you want to.

Fitting vinyl around radiator pipes

Using a utility knife to trim the excess vinyl floor which has been laid around a radiator pipe.

To fit vinyl around a pipe, make a straight cut in line with the pipe to the edge of the vinyl. Then make a series of small cuts at the pipe end of the slit until the vinyl lies flat around the pipe. Trim the slit pieces to get a neat finish.

Fitting vinyl at external corners

Sheet vinyl has been rolled back at the external corner of two walls. Vinyl is being cut in a straight line from the edge of the sheet to the corner of the two walls.

For external corners, make a straight cut from the edge of the vinyl down to the floor level and cut away the excess vinyl, leaving 50mm - 100mm turned up at the skirting.

Use a bolster chisel to press into the angle between the skirting and floor. Hold the straightedge against each crease and cut along it, holding the knife at a slight angle to get a neat finish.

Fitting vinyl around a door frame

Making a vertical cut in a piece of sheet vinyl which has been rolled back around a door frame.

To fit vinyl around a door frame, make a series of vertical cuts to the point where the vinyl meets the floor. Cut off the excess, but make sure to leave 50mm-100mm turned up at floor level for more accurate trimming.

Press the vinyl into the angle between the door frame and the floor, and cut along the crease. Then cut the vinyl straight across the line of the door so it ends half-way under it. Fit a threshold bar to hold down and protect the edge of the vinyl.

Joining vinyl sheets

Running a utility knife along a metal ruler to cut the excess from a vinyl sheet to line up the patterns.

If you're working in a large room, you might have to join two or more sheets to cover the whole floor. Try use sheets from the same roll, as different ones can vary slightly in colour and try not to create a join in the doorway, because this area gets the most wear.

If you're joining patterned sheets, you'll need to slide the second sheet along until the pattern matches the first sheet. If you're finding this difficult, try overlapping the sheets until the pattern matches, and then make a cut through both sheets using a straightedge and a knife.

Lining up two pieces of sheet vinyl along a join ready to be glued down.

Without moving the sheets, fold back the edges and use double-sided tape or adhesive to secure them to the floor. Press down firmly with both hands to glue the join.

Related Vinyl flooring articles

  • Vinyl flooring buying guide

    Updating your floor can dramatically change the look and feel of a room – even if you’re not doing a massive decorating job. And vinyl flooring is an excellent choice for your high-traffic areas.

Tag » How To Lay Vinyl Sheet Flooring