How To Program A Garage Door Opener | DODGE RAM FORUM

Menu Log in Sign up

• Home
• Forums
• LD RAM 1500 Forums
• Generation Forums
• Gen 4 Dodge Ram
• 2012 Dodge Ram Forum

KA1OTE Hey all, I am visiting my parents and forgot my copy of their house key. They have a garage with openers and it dawned on me this afternoon that I could program one of them to my truck's upper console buttons (I, II, III). Problem is, I do not have my manual with me. Can someone post instructions on how I would go about doing this? Thanks!! #1 · Oct 19, 2013 Hey all, I am visiting my parents and forgot my copy of their house key. They have a garage with openers and it dawned on me this afternoon that I could program one of them to my truck's upper console buttons (I, II, III). Problem is, I do not have my manual with me. Can someone post instructions on how I would go about doing this? Thanks!!

Best answer

#2 · Oct 19, 2013 To program it's easy... I actually have it memorized. But because I am lazy.. 1. Turn the ignition switch to the ON/RUN position. 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink button you wish to program. 3. Simultaneously press and hold both the Homelink button you want to program and the hand-held transmitter button. 4. Continue to hold buttons until the EVIC display changes from “CHANNEL # TRAINING” to “CHANNEL # TRAINED”, then release both buttons. If it has a rolling code do this after you have done the above step... 5. At the garage door opener motor (in the garage), locate the “LEARN” or “TRAINING” button. This can usually be found where the hanging antenna wire is attached to the garage door opener/device motor. Firmly press and release the “LEARN” or “TRAINING” button. On some garage door openers/devices there may be a light that blinks when the garage door opener/device is in the LEARN/TRAIN mode. NOTE: You have 30 seconds in which to initiate the next step after the LEARN button has been pressed. 6. Return to the vehicle and press the programmed HomeLink button twice (holding the button for two seconds each time). The EVIC will display “CHANNEL # TRANSMIT”. If the garage door opener/device activates, programming is complete. #6 · Jan 15, 2016 I had to press mine a 3rd time on my 2015 Laramie to get it working. This may help someone else 0 Reply Jump to post Sort by Oldest first Oldest first Newest first Most reactions #2 · Oct 19, 2013 · Best answer To program it's easy... I actually have it memorized. But because I am lazy.. 1. Turn the ignition switch to the ON/RUN position. 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink button you wish to program. 3. Simultaneously press and hold both the Homelink button you want to program and the hand-held transmitter button. 4. Continue to hold buttons until the EVIC display changes from “CHANNEL # TRAINING” to “CHANNEL # TRAINED”, then release both buttons. If it has a rolling code do this after you have done the above step... 5. At the garage door opener motor (in the garage), locate the “LEARN” or “TRAINING” button. This can usually be found where the hanging antenna wire is attached to the garage door opener/device motor. Firmly press and release the “LEARN” or “TRAINING” button. On some garage door openers/devices there may be a light that blinks when the garage door opener/device is in the LEARN/TRAIN mode. NOTE: You have 30 seconds in which to initiate the next step after the LEARN button has been pressed. 6. Return to the vehicle and press the programmed HomeLink button twice (holding the button for two seconds each time). The EVIC will display “CHANNEL # TRANSMIT”. If the garage door opener/device activates, programming is complete. #6 · Jan 15, 2016 I had to press mine a 3rd time on my 2015 Laramie to get it working. This may help someone else 0 Reply #3 · Oct 19, 2013 Thanks so much! Trained and done! #4 · Oct 20, 2013 I had to do the very same thing tonight so thanks again for the instructions. #5 · Oct 21, 2013 Great instructions; just did mine and works perfectly! I tried previously programming but to no avail; thought my garage door opener was not compatible. Thanks for the instructions! Insert Quotes Post Reply

1. ?
2. ?
3. ?
4. ?
5. ?
6. ?
7. ?
8. ?
9. ?
10. ?
11. ?
12. ?
13. ?
14. ?
15. ?
16. ?
17. ?
18. ?
19. ?
20. ?

posts 2.3M members 230K Since 2008 We’re the ultimate Dodge RAM forum to talk about the RAM 1500, 2500 and 3500 including the Cummins powered models. Show Less Full Forum Listing Explore Our Forums LD RAM General Discussions 2014 Dodge Ram Forum 2013 Dodge Ram Forum 2012 Dodge Ram Forum 2011 Dodge Ram Forum

Our Vendors

View All

• C Chrysler Warranty Direct View profile

Top Contributors this Month

View All T Tom-G 97 Replies Tred 75 Replies ForaFrank 61 Replies

Recommended Communities

Jeep Forum 788K members The Ram 1500 RHO 40 members The Ram EV 1K members

• Home
• Forums
• LD RAM 1500 Forums
• Generation Forums
• Gen 4 Dodge Ram
• 2012 Dodge Ram Forum