How To Replace A Burned-out Air Conditioning Compressor

How to replace a burned-out air conditioning or heat pump compressor

• POST a QUESTION or COMMENT about how to replace a burned-out air conditioner or heat pump compressor motor

Air conditioner or heat pump compressor motor replacement outline:

This air conditioning repair article describes the basic steps involved in replacing a burned out air conditioner compressor. Replacing an air conditioner compressor is a job for a trained service technician. Not only is the compressor motor often the most costly part in the system, but it is not a simple "bolt-in" replacement.

InspectAPedia tolerates no conflicts of interest. We have no relationship with advertisers, products, or services discussed at this website.

- Daniel Friedman, Publisher/Editor/Author - See WHO ARE WE?

What is Involved in Air Conditioner Compressor Replacement

The service technician will:

• Confirm that the compressor has failed and needs replacement. Note that a short-cycling or humming compressor may be due to other system problems - it's not always the case that the motor is actually seized. See BURNED-OUT COMPRESSOR - how to determine that the compresor motor is burned out or seized and HARD STARTING COMPRESSOR MOTORS - sometimes a start capacitor or relay replacement are all that's needed and SHORT CYCLING AC COMPRESSOR and HVAC NOISE-3 HISS HOWL HUFF HUM - where humming compressor noises are discussed
• Identify the compressor model and capacity so that a proper replacement can be obtained
• Shut down the air conditioning system, including turning off electrical power
• Remove all refrigerant from the system. Modern procedures require that the refrigerant be captured rather than released to the environment in order to reduce environmental pollutants
• If the air conditioner system used a now-obsolete refrigerant such as R11 or R22, a the new compressor will be one designed to use a new, approved refrigerant and other changes may be needed to the system to accommodate this change, such as changes in thermal-expansion valves, coils, or other components. Not all components need replacement, however; ducts and blower assemblies, for example, are retained.
• The refrigerant lines are cut and the old compressor is removed. See also REFRIGERANT PIPING INSTALLATION
• The new compressor is installed in place in the compressor/condenser unit (usually all of this equipment is located outside), and its refrigerant lines are connected (usually silver soldering) to the existing refrigerant lines. New coils or other controls may need to be cut out and replaced if the refrigerant is being changed too.
• A compressor motor burn-out filter is installed, possibly two of them on both the low and high side refrigerant lines at the compressor/condenser unit. This special HVAC compressor burnout dryer / filter may be installed on the refrigerant line(s) to provide extra debris and moisture and oil filtering capacity to protect the new equipment from debris clogging. Capillary tubes and TEVs as well as coils and compressors are vulnerable to damage or clogging from debris, stray oil, or water in the refrigerant piping system. See REFRIGERANT DRIERS & FILTERS
• A vacuum is pulled on the entire system both to evacuate all air from the refrigerant lines and compressor and to check for leaks in the system. Air contamination, if allowed to mix with the new refrigerant would change its operating characteristics and would prevent proper operation.
• Any water or moisture in the system is also removed and as we noted above, during re-connection of the refrigerant piping the technician may install a compressor burn-out filter-drier in the system to remove any trace moisture that remains behind after reassembly.
• Refrigerant is added to the system at the proper charge amount. Residential air conditioner systems, unlike commercial units, use a hermetically sealed compressor motor and there is no separate receiver to hold a large refrigerant charge, so the charge must be measured precisely (including temperature, pressure, and volume during charging) for the system to work properly. Both overcharging and under-charging refrigerants will lead to improper system operation.
• The air conditioning system, with its new compressor installed, will be re-started and checked for proper operation

...

Continue reading at CAPACITORS for HARD STARTING MOTORS or select a topic from the closely-related articles below, or see the complete ARTICLE INDEX.

Or see COMPRESSOR MOTOR REPLACEMENT FAQs - questions & answers about A/C or heat pump compressor motor replacement requirements posted originally at this page

Or see these

Recommended Articles

• BURNED-OUT COMPRESSOR
• COMPRESSOR CONDENSER - home
• DIAGNOSTIC GUIDE A/C or HEAT PUMP
• DIAGNOSTIC DETAILS A/C or HEAT PUMP
• HARD STARTING COMPRESSOR MOTORS
• TIGHT or SEIZED AC COMPRESSORS

Suggested citation for this web page

COMPRESSOR MOTOR REPLACEMENT at InspectApedia.com - online encyclopedia of building & environmental inspection, testing, diagnosis, repair, & problem prevention advice.

Share this article

Or see this

INDEX to RELATED ARTICLES: ARTICLE INDEX to AIR CONDITIONING & HEAT PUMPS

Or use the SEARCH BOX found below to Ask a Question or Search InspectApedia

Ask a Question or Search InspectApedia

Try the search box just below, or if you prefer, post a question or comment in the Comments box below and we will respond promptly.

Search the InspectApedia website

Note: appearance of your Comment below may be delayed: if your comment contains an image, photograph, web link, or text that looks to the software as if it might be a web link, your posting will appear after it has been approved by a moderator. Apologies for the delay.

Only one image can be added per comment but you can post as many comments, and therefore images, as you like. You will not receive a notification when a response to your question has been posted. Please bookmark this page to make it easy for you to check back for our response.

Comment Form is loading comments...

IF above you see "Comment Form is loading comments..." then COMMENT BOX - countable.ca / bawkbox.com IS NOT WORKING. In any case you are welcome to send an email directly to us at InspectApedia.com at [email protected]

We'll reply to you directly. Please help us help you by noting, in your email, the URL of the InspectApedia page where you wanted to comment.

Citations & References

In addition to any citations in the article above, a full list is available on request.

• Complete List of Air Conditioning & Heat Pump Design, Inspection, Repair Books at the InspectAPedia Bookstore.
• Modern Refrigeration and Air Conditioning, A. D. Althouse, C.H. Turnquist, A. Bracciano, Goodheart-Willcox Co., 1982
• Principles of Refrigeration, R. Warren Marsh, C. Thomas Olivo, Delmar Publishers, 1979
• Refrigeration and Air Conditioning Technology, 5th Ed., William C. Whitman, William M. Johnson, John Tomczyk, Cengage Learning, 2005, ISBN 1401837654, 9781401837655 1324 pages
• In addition to citations & references found in this article, see the research citations given at the end of the related articles found at our suggestedCONTINUE READING or RECOMMENDED ARTICLES.

• Carson, Dunlop & Associates Ltd., 120 Carlton Street Suite 407, Toronto ON M5A 4K2. Tel: (416) 964-9415 1-800-268-7070 Email: [email protected]. Alan Carson is a past president of ASHI, the American Society of Home Inspectors. Thanks to Alan Carson and Bob Dunlop, for permission for InspectAPedia to use text excerpts from The HOME REFERENCE BOOK - the Encyclopedia of Homes and to use illustrations from The ILLUSTRATED HOME . Carson Dunlop Associates provides extensive home inspection education and report writing material. In gratitude we provide links to tsome Carson Dunlop Associates products and services.

ADVERTISEMENT