How To Shrink Wrap A Boat (with Pictures) - WikiHow

Home » How To Shrink Wrap A Boat » How To Shrink Wrap A Boat (with Pictures) - WikiHow

Maybe your like

Skip to ContentQuizzes
  • Home
  • Random
  • Browse Articles
  • Quizzes & Games
  • All QuizzesHot
  • Love Quizzes
  • Personality Quizzes
  • Fun Games
  • Dating Simulator
  • Learn Something New
  • Forums
  • Courses
  • Happiness Hub
  • Explore More
  • Support wikiHow
  • About wikiHow
  • Log in / Sign up
Terms of Use wikiHow is where trusted research and expert knowledge come together. Learn why people trust wikiHow How to Shrink Wrap a Boat PDF download Download Article Co-authored by wikiHow Staff

Last Updated: February 24, 2025 References

PDF download Download Article
  • Moving and Securing the Boat
    • |
  • Building a Fabric Frame
    • |
  • Applying the Shrink Wrap
    • |
  • Finishing and Venting the Seal
    • |
  • Video
    • |
  • Q&A
    • |
  • Tips
    • |
  • Warnings
    • |
  • Things You'll Need
|Show more |Show less X

This article was co-authored by wikiHow Staff. Our trained team of editors and researchers validate articles for accuracy and comprehensiveness. wikiHow's Content Management Team carefully monitors the work from our editorial staff to ensure that each article is backed by trusted research and meets our high quality standards. There are 15 references cited in this article, which can be found at the bottom of the page. This article has been viewed 97,273 times. Learn more...

When you need to store your boat for the winter or ship it to a new location, use marine shrink wrap to keep it in top condition. A tight layer of shrink wrap blocks out cold air, moisture, and sunlight. To install shrink wrap, fit sheeting over a frame of polyester strapping, then warm it with a shrink gun. Add tape, vents, and doors as needed to safely seal away your boat until you’re ready to use it again.

Steps

Part 1 Part 1 of 4:

Moving and Securing the Boat

PDF download Download Article
  1. Step 1 Take the boat out of the water before wrapping it. 1 Take the boat out of the water before wrapping it. Before you can prepare your boat for winter, you need to move it to a protected location. Most marinas have lifts to transfer larger boats onto trailers and storage blocks. If you have a smaller boat, use a winch to pull the boat onto a trailer parked near the water.[1]
    • You can leave a small speedboat or sailboats on its trailer while you winterize it. If you have a larger, heavier boat like a yacht, put it on blocks for the winter.
  2. Step 2 Move the boat to a well-ventilated area for storage. 2 Move the boat to a well-ventilated area for storage. Try to find a secure storage spot inside a marina or garage. The shrink wrap releases chemicals as it is heated, so make sure you have some open doors or other ventilation nearby. Working outdoors is fine, but keep in mind that strong winds make winterizing a boat very difficult. If you have to work outdoors, choose a clear, windless day.[2]
    • To protect yourself from any fumes released by the shrink wrap, wear a respirator or dust mask.
    • If you can, bring the boat to its winter storage location before winterizing it. That way, you don’t have to move it later and risk damaging the wrapping.
    Advertisement
  3. Step 3 Cover fuel vents with shrink wrap tape to seal them. 3 Cover fuel vents with shrink wrap tape to seal them. To protect your boat, turn off the fuel line valve. Drain any remaining fuel out of the line, if possible. Then, completely seal the vents to prevent heat from igniting fuel vapors. Use as much tape as you need to block off the vents.[3]
    • You can get shrink wrap tape online from marine supply stores and shrink wrap suppliers. Also, look for it at hardware or general stores.
    • Consult the boat manufacturer or your owner’s manual to find the vents if you’re not sure where they are.
  4. Step 4 Pad sharp corners with foam cushions or towels. 4 Pad sharp corners with foam cushions or towels. Sharp pieces are threats to a shrink wrap seal. Cover them completely to blunt them. Tape cushioning to them with shrink wrap tape or something similar. Make sure the shrink wrap can rest against these edges without breaking.[4]
    • You can purchase foam insulation from a hardware store or repurpose some old towels or clothing.
    • Some areas to cover include windshield corners, antennas, and ski pylons.
    5. Advertisement
Part 2 Part 2 of 4:

Building a Fabric Frame

PDF download Download Article
  1. Step 1 Set up support posts along the center of your boat. 1 Set up support posts along the center of your boat. The support posts belong in the open areas on the boat’s deck. Each post needs a bottom and top cap to hold it in place properly. Place the first post near the bow, making sure it’s at least 10 in (25 cm) above the highest point in your boat. Place a second post near the boat's stern.[5]
    • If you wish to make your own posts, measure the boat’s height from the deck to the highest point. Purchase 2 in × 4 in (5.1 cm × 10.2 cm) wood posts 10 in (25 cm) taller than your measurement, then fit them with foam caps purchased online.
    • You only need 2 posts for small powerboats. Place additional posts to support the shrink wrap on larger boats. Install an additional post for every 8 ft (2.4 m) of boat length you need to cover.
  2. Step 2 Tie the support posts in place with polyester straps. 2 Tie the support posts in place with polyester straps. Run a support strap from the back end of the boat to the front. Thread it through the grooves on the support post caps. Then, lay more straps side to side across the boat, including a single strap through each cap. Buckle all of the straps to grab rails or cleats along the boat’s edges to keep them locked in place.[6]
    • Make sure the straps are tight and secure. They form a stable frame to fit the shrink wrap over. If the straps look loose, the shrink wrap will also be loose.
    • If you can’t find a place to anchor the strapping, run it all the way down to the trailer underneath the boat.
  3. Step 3 Tie loops to the end of each piece of strapping. 3 Tie loops to the end of each piece of strapping. Measure from the end of the strapping to about 8 in (20 cm) below the metal rub rail around the edge of the boat. Cut new straps to length, then tie the straps to the cleats and edge rails. Shape the free ends of the straps into well-tied loops about 1⁄2 in (1.3 cm) in size.[7]
    • Tie the straps in place using a basic overhand knot. Using a different kind of knot is also fine as long as the straps are well-secure.
  4. Step 4 Wrap a perimeter band all the way around the boat. 4 Wrap a perimeter band all the way around the boat. Start at the rear or stern end of the boat. Run a new piece of strapping through each of the loops you tied, making sure it fits tightly against the boat’s side. When you get back to the stern, tie the ends of the strap together with a buckle.[8]
    • Pull the strap as tight as you can before tying it. For assistance, use a strap tensioning tool, available online and in most shrink wrap kits.
    • You can tie the perimeter band around the boat’s propeller. Use it as an anchor point to keep the strap tight and secure.
    5. Advertisement
Part 3 Part 3 of 4:

Applying the Shrink Wrap

PDF download Download Article
  1. Step 1 Measure your boat’s height and length to figure out how much material you need. 1 Measure your boat’s height and length to figure out how much material you need. Use a tape measure to measure from the center of the boat down to the metal rub rail on the side. Add an extra 8 in (20 cm) so the sheet reaches the perimeter band you install later. Then, add another 6 in (15 cm) to fold underneath the band. Double your estimate to account for the other side of the boat.[9]
    • The shrink wrap also needs to cover the entire top of the boat, including the windshields and other protrusions. Measure down from the highest point of the boat, which is usually one of the supports you set up earlier.
    • Keep in mind that using too much shrink wrap is better than not having enough. You can always cut a bigger sheet down to size before you heat it.
  2. Step 2 Drape the shrink wrap and tuck it around the perimeter band. 2 Drape the shrink wrap and tuck it around the perimeter band. Apply the shrink wrap film by starting from the top of the support post and working your way down to the hull. The shrink wrap needs to be long enough to reach the perimeter band. Leave an extra 6 in (15 cm) on all sides to cover the perimeter band. Cut off the excess material as needed with a film knife.[10]
    • Keep the wrap folded in a box until you are ready to use it. It may tear or get dirt on it if you aren’t careful.
    • Try to use a single piece of shrink wrap to cover the entire boat. If you need to use 2 pieces, join them with shrink wrap tape and heat.
  3. Step 3 Weld the shrink wrap to the perimeter band with a heat tool. 3 Weld the shrink wrap to the perimeter band with a heat tool. Put on a heat-resistant glove to protect your hand as you work. Hold the heat gun slightly above the edge of the shrink wrap. Work all the way around the boat, lightly heating and patting down the tucked-in edge. Leave the back edge of the boat alone for now.[11]
    • The heat wrap will get warm, so be careful not to touch it with exposed skin. Also, use gentle amounts of heat to avoid damaging the wrap or your boat.
  4. Step 4 Tie belly bands every 6 in (15 cm) along the shrink wrap. 4 Tie belly bands every 6 in (15 cm) along the shrink wrap. Measure the distance along the trailer, tying polyester strapping to it. Use your film knife to cut small slits in the shrink wrap. Then, thread the strapping through the slits. Knot the strapping tightly and cut off the excess material.[12]
    • The belly bands keep the shrink wrap film pulled tight, leading to a better seal.
    • You do not need to tighten the belly bands further. As long as they are about 8 in (20 cm) below the rub rail, tying them once is enough.
  5. Step 5 Secure the shrink wrap to the back end of the boat. 5 Secure the shrink wrap to the back end of the boat. Head to the stern, then begin tucking the shrink wrap like you did for the boat’s other sides. Cut off the excess material as needed after covering the propeller or any other exposed parts. Then, heat the edge of the shrink wrap to flatten and secure it to the boat. If you need to, reach underneath the stern to heat the shrink wrap from the opposite angle.[13]
    • This part is the trickiest to get right. The film may tear if you work too quickly. When you’re done, the shrink wrap will hang lower than it does on the rest of the boat.
  6. Step 6 Heat the wrap from the back to the front of the boat. 6 Heat the wrap from the back to the front of the boat. Hold the heat gun about 6 in (15 cm) above the boat. Work on 1 side of the boat at a time, starting near the rub rail. Move the gun steadily towards the front of the boat while heating the sheeting flat. Remember to use your gloved hand as needed to smooth out any wrinkles you notice.[14]
    • If you have ever tried spray painting, heating shrink wrap requires a similar motion. As long as you keep the gun moving at a steady pace, you can avoid melting the sheeting or the boat.
    • To avoid overheating or melting the wrap, keep track of the areas you have worked on. Think of the boat as being divided into sections. Work on a single section at a time.
  7. Step 7 Use a ladder or extension to reach the top part of the boat. 7 Use a ladder or extension to reach the top part of the boat. The safest way to shrink the uppermost part of the sheeting is with an extension. Secure the heat gun in an extension tool, then hold it up over the wrap. Work from the back to the front of the boat until the entire sheet looks flat and wrinkle-free.
    • If you use a ladder, make sure you are able to reach the top part of the boat without falling. Touching the shrink wrap may damage it.
    8. Advertisement
Part 4 Part 4 of 4:

Finishing and Venting the Seal

PDF download Download Article
  1. Step 1 Tape over any holes or weak points you notice in the shrink wrap. 1 Tape over any holes or weak points you notice in the shrink wrap. Cover over holes with a thick layer of sheet wrap tape. Then, warm the tape up briefly with a heat gun to cause it to stick to the shrink wrap. In addition to the holes, tape over noticeable seams joining shrink wrap sheets together.[15]
    • The tape adheres better when the shrink wrap is still warm. If you have to let the shrink wrap cool, you may need to warm it up very briefly again to get the tape to stick.
    • Read the manufacturer’s recommendations on the shrink wrap tape for more specific instructions about how to cover up damaged spots.
  2. Step 2 Place adhesive vents along the sides of the boat. 2 Place adhesive vents along the sides of the boat. The vents fit on the top side of the boat above the deck. You will need 4 to 6 vents for a small powerboat. Space these out along the boat, placing a vent close to each corner. Stick them directly onto the shrink wrap.
    • A great place for the vents is over your boat’s taped up fuel vents.
    • The vents let moisture out from underneath the shrink wrap, preventing mold from growing on your boat.
    • To figure out how many vents you need, refer to a size guide. Try using https://dr-shrink.com/boat-size-venting-chart-cheat-sheet/.
  3. Step 3 Cut open the vent before installing a cap over it. 3 Cut open the vent before installing a cap over it. Use a film knife to slice away the shrink wrap inside the vent opening. Then, fit the cap in place. It comes included with any vents you get. Once all of the vent caps have been firmly lodged onto the vent, you’re done with the main winterization process.[16]
  4. Step 4 Install a zippered door if you need to enter the boat. 4 Install a zippered door if you need to enter the boat. Installing a zippered door is similar to installing a vent. Find an accessible spot on top of your boat, then lay the door over the shrink wrap. Tape the door in place before cutting out the opening. Pull the zipper to close the door until you need to climb inside the boat.
    • Most shrink wrap manufacturers offer zippered doors. Zippered doors do not break the shrink wrap seal you worked so diligently to install, so add a door if you think you will need to get into the boat during the winter.
    5. Advertisement

Community Q&A

Search Add New Question
  • Question Should I take the seat covers off before I wrap the boat? Community Answer Community Answer Depends what they are made of. If they are also PVC, then it might melt together with the wrap. If they are vinyl, then you should be good. Thanks! We're glad this was helpful. Thank you for your feedback. If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow Yes No Not Helpful 3 Helpful 1
  • Question Is shrink wrap good in high humidity environments like Florida? Will it make a boat moldy? Brett Gilbert Brett Gilbert Top Answerer You can do it, but try to get your boat as dry as possible before wrapping it. Any leftover moisture increases the chance of mold. Use vents to help drain out the moisture, and store your boat in a relatively cool, dry place, if possible. Thanks! We're glad this was helpful. Thank you for your feedback. If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow Yes No Not Helpful 1 Helpful 1
  • Question Should you shrink wrap over a custom cover for added protection? Brett Gilbert Brett Gilbert Top Answerer You don't need to. Your best bet would be to choose either the cover or the shrink wrap. The cover may get damaged from the heat or block in moisture. Thanks! We're glad this was helpful. Thank you for your feedback. If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow Yes No Not Helpful 0 Helpful 0
Ask a Question 200 characters left Include your email address to get a message when this question is answered. Submit Advertisement

Video

Tips

  • Remove shrink wrap by cutting it with a plastic edge. Using a sharp knife or a similar object may scratch up your boat. Thanks Helpful 0 Not Helpful 0
  • To fully winterize your boat, remove cushions and other fabric components. If you can’t remove them, leave the boat’s doors open to ventilate the cabins. Thanks Helpful 0 Not Helpful 0
Submit a Tip All tip submissions are carefully reviewed before being published Name Please provide your name and last initial Submit Thanks for submitting a tip for review! Advertisement

Warnings

  • Shrink wrap is flammable when it is overheated. Always keep a fire extinguisher on hand in case of an emergency. Thanks Helpful 0 Not Helpful 0
  • You can damage your boat while attempting to shrink wrap it. If you’re worried about this, hire a professional. Thanks Helpful 0 Not Helpful 0
  • Shrink wrap releases a toxic odor when it is heated. Work in a ventilated space and wear a respirator. Thanks Helpful 0 Not Helpful 0
Advertisement

Things You'll Need

  • Measuring tape
  • Shrink wrap
  • Heat gun
  • Padding for sharp edges
  • Film knife
  • Shrink wrap tape
  • At least 4 vents
  • At least 2 2 in × 4 in (5.1 cm × 10.2 cm) posts approximately 10 in (25 cm) tall
  • Zippered door

You Might Also Like

Shrink WrapHow toShrink Wrap Install Window Insulation FilmHow toInstall Window Insulation Film Shrink Wrap a PalletHow toShrink Wrap a Pallet Apply Vinyl WrapHow toApply Vinyl Wrap Install Weather StrippingHow toInstall Weather Stripping Wrap Homemade SoapHow toWrap Homemade Soap Tie up a BoatHow to Tie a Boat to a Dock Winterize a Jet SkiHow toWinterize a Jet Ski How toPackage a Painting for Shipping Pack Furniture For MovingHow to Pack (& Protect) Furniture When You're Moving Encapsulate Your CrawlspaceHow toEncapsulate Your Crawlspace Pack PaintingsHow toPack Paintings Fiberglass a BoatHow toFiberglass a Boat How toDo Cellophane Wrapping Advertisement

References

  1. ↑ http://www.withoutahitch.com.au/marine/getting-boat-water-step-step-guide/
  2. ↑ https://www.discoverboating.com/ownership/storage
  3. ↑ https://www.boatingmag.com/how-to/should-you-shrinkwrap-your-own-boat
  4. ↑ https://www.boatingmag.com/how-to/should-you-shrinkwrap-your-own-boat
  5. ↑ https://www.youtube.com/watch?v=eg7sjGw0SZY&feature=youtu.be&t=91
  6. ↑ https://www.youtube.com/watch?v=l0gLOh4ZFJ8&feature=youtu.be&t=11
  7. ↑ https://www.youtube.com/watch?v=vm3OQEI8GQg&feature=youtu.be&t=142
  8. ↑ https://www.youtube.com/watch?v=tJs7o0LZiRo&feature=youtu.be&t=327
  9. ↑ https://www.youtube.com/watch?v=vm3OQEI8GQg&feature=youtu.be&t=235
More References (7)
  1. ↑ https://www.youtube.com/watch?v=uJ6X-CfB0uc&feature=youtu.be&t=559
  2. ↑ https://www.youtube.com/watch?v=l0gLOh4ZFJ8&feature=youtu.be&t=41
  3. ↑ https://www.youtube.com/watch?v=l0gLOh4ZFJ8&feature=youtu.be&t=65
  4. ↑ https://www.youtube.com/watch?v=IxjaiZsF5Uw&feature=youtu.be&t=614
  5. ↑ https://www.youtube.com/watch?v=tJs7o0LZiRo&feature=youtu.be&t=1249
  6. ↑ https://www.youtube.com/watch?v=IxjaiZsF5Uw&feature=youtu.be&t=776
  7. ↑ https://www.youtube.com/watch?v=vm3OQEI8GQg&feature=youtu.be&t=451

About This Article

wikiHow Staff Co-authored by: wikiHow Staff wikiHow Staff Writer This article was co-authored by wikiHow Staff. Our trained team of editors and researchers validate articles for accuracy and comprehensiveness. wikiHow's Content Management Team carefully monitors the work from our editorial staff to ensure that each article is backed by trusted research and meets our high quality standards. This article has been viewed 97,273 times. 14 votes - 71% Co-authors: 7 Updated: February 24, 2025 Views: 97,273 Categories: Boats In other languagesJapanese
  • Print
  • Send fan mail to authors
Thanks to all authors for creating a page that has been read 97,273 times.

Reader Success Stories

  • Mons Jahmin

    Mons Jahmin

    Apr 27, 2018

    "I brought my boat in, and they wrote the wrong name on the shrink wrap. This resulted in my boat "being..." more Rated this article:
Share your story

Did this article help you?

Yes No Advertisement Cookies make wikiHow better. By continuing to use our site, you agree to our cookie policy. wikiHow Staff Co-authored by: wikiHow Staff wikiHow Staff Writer 14 votes - 71% Click a star to vote Co-authors: 7 Updated: February 24, 2025 Views: 97,273 Mons Jahmin

Mons Jahmin

Apr 27, 2018

"I brought my boat in, and they wrote the wrong name on the shrink wrap. This resulted in my boat "being..." more Rated this article: Share yours!

Quizzes & Games

How Good Are My Survival Instincts QuizHow Good Are My Survival Instincts QuizTake QuizCan You Spot The False Climate Claims QuizCan You Spot The False Climate Claims QuizTake QuizWhat Kind of Reality Check Do I Need QuizWhat Kind of Reality Check Do I Need QuizTake QuizWhat Are The Best Compression Socks For Me QuizWhat Are The Best Compression Socks For Me QuizTake QuizBedroom Aesthetic QuizBedroom Aesthetic QuizTake QuizHow Will I Die QuizHow Will I Die QuizTake Quiz

You Might Also Like

Shrink WrapHow toShrink WrapInstall Window Insulation FilmHow toInstall Window Insulation FilmShrink Wrap a PalletHow toShrink Wrap a PalletApply Vinyl WrapHow toApply Vinyl Wrap

Featured Articles

Remove Shorts from Search Results on YouTubeHow toRemove Shorts from Search Results on YouTubeWhat Are the Korean Animal Face Types? (And Which Type Do You Have?)What Are the Korean Animal Face Types? (And Which Type Do You Have?)Being the Little Spoon While Cuddling: Is It Better Than the Big Spoon?Being the Little Spoon While Cuddling: Is It Better Than the Big Spoon?115+ Funny “Get Well Soon” Messages to Make Someone Laugh115+ Funny “Get Well Soon” Messages to Make Someone Laugh110+ “Fun Facts” for Interviews, Introductions, & Icebreakers110+ “Fun Facts” for Interviews, Introductions, & IcebreakersHow Long Would You Survive In A Zombie Apocalypse?How Long Would You Survive In A Zombie Apocalypse?

Trending Articles

Which Fictional Character Would Crush On You?Which Fictional Character Would Crush On You?Who Is Secretly Crushing On Me Right Now QuizWho Is Secretly Crushing On Me Right Now QuizAttractiveness Score QuizAttractiveness Score QuizIs My Crush Pretending Not to Like Me QuizIs My Crush Pretending Not to Like Me QuizHypersexuality TestHypersexuality TestWhat Are the Gay Male Body Types (And Which Do You Have?)What Are the Gay Male Body Types (And Which Do You Have?)

Featured Articles

Roast Someone in a Rap Battle (Plus the Best Bars of All Time)How to Roast Someone in a Rap Battle (Plus the Best Bars of All Time)What Turns a Girl On? 31 Things to Try on Your PartnerWhat Turns a Girl On? 31 Things to Try on Your PartnerLove AnalyzerLove AnalyzerSending Your Sweetie a Love Note? Here are 200+ Romantic IdeasSending Your Sweetie a Love Note? Here are 200+ Romantic IdeasExercise Your BrainHow toExercise Your BrainBe a Fun Person to Hang out WithHow toBe a Fun Person to Hang out With

Featured Articles

What Does Your Morning Routine Say About You?What Does Your Morning Routine Say About You?Develop Productive HabitsHow toDevelop Productive HabitsPractice Self CareHow toPractice Self CareWhat Song Matches Your Life Right Now?What Song Matches Your Life Right Now?Will 2026 Be Your Year? Reveal Your FutureWill 2026 Be Your Year? Reveal Your FutureUnderstanding the Most Attractive Face Shapes (& Determining Your Own)Understanding the Most Attractive Face Shapes (& Determining Your Own)

Watch Articles

Tie a Loop KnotHow toTie a Loop KnotMake Body OilHow toMake Body OilMake Almond MilkHow toMake Almond MilkWash White Clothes by HandHow toWash White Clothes by HandSkin a ChickenHow toSkin a ChickenClean Tile Floors with VinegarHow toClean Tile Floors with Vinegar

Trending Articles

What Are My Soulmate's Initials QuizWhat Are My Soulmate's Initials QuizChoose Your Own Adventure GameChoose Your Own Adventure GameYour Red Flag Based On Your Celeb CrushesYour Red Flag Based On Your Celeb Crushes151 of the Juiciest “Most Likely To” Questions to Ask151 of the Juiciest “Most Likely To” Questions to AskAm I Good at Flirting QuizAm I Good at Flirting QuizWhat Is Your Lip Type?What Is Your Lip Type?

Quizzes & Games

What Makeup Should I Wear QuizWhat Makeup Should I Wear QuizTake QuizWhy Can't I Sleep QuizWhy Can't I Sleep QuizTake QuizWould I Be a Good Super Spy QuizWould I Be a Good Super Spy QuizTake QuizWhat Do I Want in a Weight Loss Program QuizWhat Do I Want in a Weight Loss Program QuizTake QuizWhat Wild wikiHow Article Am I QuizWhat Wild wikiHow Article Am I QuizTake QuizWhat Sea Creature Am I QuizWhat Sea Creature Am I QuizTake Quiz wikiHow
  • Categories
  • Cars & Other Vehicles
  • Boats
wikiHow Newsletter You're all set! Helpful how-tos delivered toyour inbox every week! Sign me up! By signing up you are agreeing to receive emails according to our privacy policy.
  • Home
  • About wikiHow
  • Experts
  • Jobs
  • Contact Us
  • Site Map
  • Terms of Use
  • Privacy Policy
  • Do Not Sell or Share My Info
  • Not Selling Info
  • Contribute

Follow Us

×

Don’t miss out! Sign up for

wikiHow’s newsletter

Subscribe You're all set! X --730

Tag » How To Shrink Wrap A Boat