Outside Diameter Definition | Law Insider

Outside Diameter definitionOutside Diameter also referred to as “OD” means the points of measurement, using the outer edges of a pole, pipe or cylinder.View SourceBased on 7 documents7Draft with AISplit ViewAI-Powered Contracts

Draft, Review & Redline at the Speed of AI

Get StartedBook a DemoOutside Diameter or “OD” means the points of measurement, using the outer edges of a pole, pipe or cylinder.View SourceBased on 6 documents6Draft with AI

Examples of Outside Diameter in a sentence

• IS 3589 Steel Pipes for Water and Sewage (168.3 to 2540 mm Outside Diameter) IS 3600 Code of Procedure for Testing of Fusion Welded Joints and Weld- Metal in Steel.

• Minimum pipe wall thickness shall yield less than 20% SMYS according to the following formula: %SMYS Calculation: D*Pa/(2*wt)/Y*100=%SMYS D= Outside Diameter of Pipe in inches Pa= MAOP in psia Wt= Wall Thickness in inches Y= Yield Strength in pounds Welded joints, fittings and damaged areas of the coating shall be wrapped with a tape coating having a minimum thickness of 35 mils and shall be compatible with the specified coating.

• Nominal Size Outside Diameter Weight Per Foot 6 6.625 18.97 8 8.625 24.70 10 10.750 34.24 12 12.750 43.77 14 14.000 54.57 16 16.000 62.58 Pipe shall be furnished in interchangeable sections of 20-foot nominal length for enclosed line shaft and 10-foot length for open line shaft, with the exception of the top column section which shall be of 5-foot nominal length and the bottom column section which may be of shorter length.

• Manufacture ▇▇▇▇▇ Sobelco Number of Tubes: Cold Condensers Hot Condensers 22 552 23 730 Condenser Height: Overall Neck Shell 10 300 mm 5 450 mm 4 580 mm Condenser Length: Overall (between water box centers) Cold Condensers Hot Condensers 24 600 mm 12 000 mm 12 600 mm Tube Length Cold Condensers Hot Condensers 9992 mm 10.922 mm Tube Outside Diameter Re-Tubed:  General sections: 19mm OD with a 0.5mm wall.

• When considering a plus size application for a vehicle, parameters include the Original Equipment Tire Size, Speed Rating, Load Capability, Inflation Pressures, Outside Diameter (Overall Tire Diameter), and Revolutions Per Mile, as well as the space limitations of the vehicle wheel well.

• The transition coupling for HDPE to PVC and PVC to steel conduit for entrance conduits shall take place at the top of the trench six inches below ground after sweeps or bends to the building in compliance with ASTM F 2160 -Standard Specification for Solid Wall High Density Polyethylene (HDPE) Conduit Based on Controlled Outside Diameter (OD), and ASTM F 2176 - Standard Specification for Mechanical Couplings Used on Polyethylene Conduit, Duct and Innerduct.

• IS 3589 Steel Pipes for Water and Sewage (168.3 to 2540 mm Outside Diameter) IS 3600 Code of Procedure for Testing of Fusion Welded Joints and Weld-Metal in Steel.

• Nominal Diameter Mean Outside Diameter of the Pipe Outside Diameter of the pipe at any Point Wall Thickness Min Max Min Max Min Max 75 A 75.00 75.30 74.10 75.90 1.80 2.20 75 B 75.00 75.30 74.10 75.90 3.20 3.80 90 A 90.00 90.30 88.90 91.20 1.90 2.30 90 B 90.00 90.30 88.90 91.20 3.20 3.80 110 A 110.00 110.40 108.60 111.40 2.20 2.70 110 B 110.

• Steel H-Pile HP310x125 950 Steel Pipe Pile 300 mm Outside Diameter x 9.52 mm- thick-walled Pipe Pile 550 *The capacities noted herein were not adjusted to include the pile dead load.

• Thickness mils Feed trunnion, live load kN Feed trunnion, dead load kN Discharge trunnion, live load kN Discharge trunnion, dead load kN Mill Type: Diameter Inside Shell mm Shell Length, Flange to Flange mm Grinding Chamber Length mm Volume Inside Liners m3 Mill Operating Speed rpm Percent of Criticial speed (new liners): % Power Required with New liners at Design Ore & Media Charge kW Head Outside Diameter mm Feed end Trunnion Min.

Related to Outside Diameter

• Outside Directors means members of the Board who are not officers of the Company or any of its Subsidiaries and who are not Acquiring Persons or representatives, nominees, Affiliates or Associates of Acquiring Persons.

• Outside Director means a Director who is not an Employee.

• Section 162(m) means Section 162(m) of the Code.

• Section 162(m) of the Code means the exception for performance-based compensation under Section 162(m) of the Code and any applicable treasury regulations thereunder.

• Section 162(m) Award means a Performance Award granted under Section 6(k)(i) to a Covered Employee that is intended to satisfy the requirements for “performance-based compensation” within the meaning of Section 162(m).

Filter & Search

Definition: Outside DiameterContract TypeJurisdictionCountryInclude KeywordsExclude Keywords

Additional filters are available in search

Open Search

Related Definitions

• Outside Directors
• Outside Director
• Section 162(m)
• Section 162(m) of the Code
• Section 162(m) Award