Range Rover Evoque - Audio Front Control Module (ACM) - Low Line

Range Rover Evoque: Audio Front Control Module (ACM) - Low Line Land Rover Range Rover Evoque L538 (2011–2018) Service Manual / Description and Operation / General Information / Diagnostic Trouble Code (DTC) Index DTC / Audio Front Control Module (ACM) - Low Line

Audio Front Control Module - Low Line (ACM)

CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle.

NOTES:

If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty Policy and Procedures manual (section B1.2), or determine if any prior approval programme is in operation, prior to the installation of a new module/component.

Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the manufacturer-approved diagnostic system).

Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.

Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.

If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the cause. Always check for loose connections and corroded terminals.

The table below lists all Diagnostic Trouble Codes (DTCs) that could be logged in the Audio Front Control Module - Low Line (ACM), for additional Diagnosis and Testing information refer to the relevant Diagnosis and Testing Section.

For additional information, refer to: Information and Entertainment System (415-01 Information and Entertainment System, Diagnosis and Testing).

Multi-Information Display Unit (MFD)

Multifunction Display Module (FCDIM) - Low Line

CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle.

NOTES:

If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty Policy and Procedures manual (section B1.2), or determine if any prior approval programme is in operation, prior to the installation of a new module/component.

Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the manufacturer-approved diagnostic system).

Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.

Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.

If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the cause. Always check for loose connections and corroded terminals.

The table below lists all Diagnostic Trouble Codes (DTCs) that could be logged in the Multifunction Display Module, for additional Diagnosis and Testing information refer to the relevant Diagnosis and Testing Section.

For additional information, refer to: Information and Entertainment System (415-01 Information and Entertainment System, Diagnosis and Testing).

READ NEXT:

Touch Screen (TS)

Touch Screen Display (FCDIM) The table below lists all Diagnostic Trouble Codes (DTCs) that could be logged in the Multifunction Display Module, for additional Diagnosis and Testing information refer

Blind Spot Monitoring Module (SODL/SODR)

Blind Spot Monitoring System Module (SODL/SODR) CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not guarantee confirmation of a

Health and Safety Precautions

Introduction Modern vehicles contain many materials and liquids which if not handled with care can be hazardous to both personal health and the environment. Also, many of the procedures associated wi

SEE MORE:

Power Flows

Operation of the transmission is controlled by the TCM which electrically activates various solenoids to control the transmission gear selection. The sequence of solenoid activation is based on programmed information in the TCM memory and physical transmission operating conditions such as vehicle

Control Diagram, System Operation

Control Diagram NOTE: A = Hardwired; F = RF transmission; N = Medium speed CAN (controller area network) bus; O = LIN (local interconnect network) bus. Instrument cluster CJB (central junction box) Radio frequency (RF) receiver RFA (remote function actuator) / KVM (keyless vehicle module) Re