SRS Airbag Control Module Location Lookup - MyAirbags

Airbag Module Location

For part location in vehicle select Make, Model, Year

Select Make...

1. Select Make...
2. ACURA
3. ALFA ROMEO
4. AUDI
5. BMW
6. BUICK
7. CADILLAC
8. CHEVROLET
9. CHRYSLER
10. DAEWOO
11. DODGE
12. EAGLE
13. FERRARI
14. FIAT
15. FISKER
16. FORD
17. GEO
18. GMC
19. HONDA
20. HUMMER
21. HYUNDAI
22. INFINITI
23. INTERNATIONAL
24. ISUZU
25. JAGUAR
26. JEEP
27. KIA
28. LAMBORGHINI
29. LAND ROVER
30. LEXUS
31. LINCOLN
32. LOTUS
33. MASERATI
34. MAZDA
35. MCLAREN
36. MERCEDES
37. MERCEDES-BENZ
38. MERCURY
39. MINI
40. MITSUBISHI
41. MV-1
42. NISSAN
43. OLDSMOBILE
44. PLYMOUTH
45. PONTIAC
46. PORSCHE
47. RAM
48. SAAB
49. SATURN
50. SCION
51. SMART CAR
52. SUBARU
53. SUZUKI
54. TESLA
55. TOYOTA
56. VOLKSWAGEN
57. VOLVO
58. WINNEBAGO
59. WORKHORSE

Select Model...

1. Select Model...

Select Year...

1. Select Year...

HOW TO: Removal Videos

Place your reset order

Failure to follow instructions below may result in the accidental deployment of “air bag”, “seat belt”, which increases the risk of serious personal injury or death.

• Never probe the electrical connectors on air bag or seat belt.
• Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
• Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
• Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.

To remove your airbag control module, follow these steps:

1. First find the srs computer module. In most cars it is under the center console that is between the two front seats, or center of the dash on the floor. In most GM cars it is under the driver or passenger seat.
2. Disconnect the positive battery cable and wait 3 min.
3. You are now safe to unplug the airbag control module harness wiring plugs.

To install your airbag control module:

1. All airbag srs components must be installed and connected properly before installing the airbag control module. This includes air bags, seat belts, clock spring and impact sensors.
2. Disconnect the battery and bolt down the module and then connect the harness wiring plugs.
3. Wait 3 minutes before installing the airbag module in the vehicle.
4. Bolt down module with all bolts and then connect harness plugs. (if not then, could deploy roof airbags and seat belts)
5. Vehicle needs to be flat on the ground. Not elevated on a jack or lift. (if not then, could deploy roof airbags and seat belts)
6. Reconnect battery cables.

Disclaimer: The buyer assumes all risks associated with removing, installing, and usage of a re-manufactured part(s). If you have additional questions please call us at 888-779-9029 or submit a request.

Place your reset order ×

• My account
• Contact us
• Shipping Address
• Airbag Module Reset
• Seat Belt Repair
• Color Seat Belts
• Webbing Replacement
• Airbag & Seat Belt Plugs
• All Services
  • Post Collision R&R Services
    • Seat Belt Repair
    • Airbag module reset
    • Collapsible Steering Column
    • Buckle Repair
    • Battery terminal fuse repair
    • In Stock & Exchange
    • Webbing Replacement
  • How it works
    • Airbag Module Reset
    • Seat Belt Repair
    • Shipping Instructions
• Express Mode
• FAQ
• Track Order
• How It Works
• Custom Request

888-779-9029