ASM Unit Converter
| Unit Converter |
| Input value: | | Convert from: | °C °F µin/in-°F µm/m-°C atm bar BTU BTU/ft-hr-°F BTU/lb BTU/lb-°F BTU-in/hr-ft²-°F cal cal cm/sec-cm²-°C cal/g cal/g-°C cc cc/100 in²/day cc/kg cc/m²/day cc/m²-24hr-atm cc-mil/100 in²-24hr-atm cc-mm/m²-24hr-atm cm cm/cm cm/cm-°C cm/cm² cm/s cm² cps day denier dtex dynes ft ft/min ft/s ft² ft²/gal ft²/lb ft²/oz ft³ ft³/min (CFM) ft-lb ft-lb in /hr-ft²-°F ft-lb/in ft-lb/in² ft-lb/in³ g g/100 in²/day g/25 mm g/cc g/denier g/in g/m² g/m²/day g/micron g/mil GPa hour hours hundredweight (cwt) in in/in-°F in/in² in/min in/sec in² in²/lb in³ in³/lb in-lb in-lb/in³ J J m/min-m²-°C J/cm J/cm² J/cm³ J/g J/g-°C J/m kcal/m-hr-°C kcal-m/hr-m²-°C kg kg(f)/cm kg(force)/cm² kg(force)/m² kg/cm² kg/m³ kg-cm/cm kJ/m² km km/h kN/m ksi kV/cm kV/in kV/mm l l/min lb lb (f) lb (weight) lb/ft² lb/ft³ lb/gal lb/in lb/in³ lb/ream lbf-s/ft² lbf-s/in² m m/s m² m²/g m³ m³/s Megaohm/1000 ft Megaohm/1000 m Mhos/cm microns mil miles (statute) min mm mm of Hg (0°C) mm/min mm/sec mm² MPa MPa-m/sec MPa-m½ mph N N/mm N/tex N-s/m² ohm-cir-mil/ft ohm-cm ohm-in ohm-m oz Pa Pascal-second pli poise poiseuille ppm psi psi-ft/min psi-ft/sec reyn sec Siemens/cm tex tons (long) tons (metric) tons (short) torr V/cm V/in V/mil V/mm W/m-°C W/m-K | |
| |
| Units |  | Value |
| Original Value * | | BTU-in/hr-ft²-°F | 1160 |
| |
| Equivalent Values | BTU/ft-hr-°F | 96.66666 |
| cal cm/sec-cm²-°C | 0.400084 |
| ft-lb in /hr-ft²-°F | 902072.8 |
| J m/min-m²-°C | 10031.51 |
| kcal-m/hr-m²-°C | 143.9444 |
| lb/s-°F | 20.87536 |
| W/m-°C | 167.3044 |
| W/m-K | 167.156 |
| |
* This indicates the value as it was originally entered into MatWeb.
For the purpose of standardization and display, MatWeb will occasionally convert an original data point to an equivalent unit of measure and round the converted value. This can introduce error if the converted and rounded value is used in an engineering calculation. MatWeb advises users to only use the original value in engineering calculations to minimize error. The original value for any point can be obtained by clicking on the data point displayed in the datasheet. This will display the data point as it was originally entered into the database as well as the raw conversions for equivalent units.