Cisco Catalyst 1000 Series 8-Port And 16-Port Switch Hardware ...

Warning

To reduce the risk of electric shock, disconnect all power cords before servicing.

Warning

The switch is to be connected only to PoE networks without routing to the outside plant.

Warning

Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals. Statement 43

Warning

Do not stack the chassis on any other equipment. If the chassis falls, it can cause severe bodily injury and equipment damage. Statement 48

Warning

Read the wall-mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system. Statement 378

Warning

Connect USB Device to a Certified USB Port. Statement 388

Warning

To avoid or reduce the risk of personal injury, do not use the product if the product has been exposed to irregular environmental conditions, if the product has been misused or if parts of the product have been damaged. Consult qualified service personnel. Never try to service the product yourself. Statement 0416

Warning

To reduce the risk of electric shock, fire or personal injury, do not place power cables in areas where they may be walked on or damaged by items placed upon or against it. Statement 0417

Warning

This product is intended for use in a normal environment based on the standard IEC60950-1 and IEC62368-1. Do not use the product in vehicles, on board ships, in aircrafts or in medical applications with physical connection to the patient, nor in environments with exposure to moisture, dust, vibration or ingress of water. Statement 0418

Warning

Equipment is intended for installation in Information Technology Equipment Rooms. Suitable for installation in Information Technology Rooms in accordance with Article 645 of the National ElectricalCode and NFPA 75. Statement 0444

Warning

Do not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001

Warning

Read the installation instructions before connecting the system to the power source. Statement 1004

Warning

Class 1 laser product. Statement 1008

Warning

There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. Statement 1015

Warning

This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security. Statement 1017

Warning

Take care when connecting units to the supply circuit so that wiring is not overloaded. Statement 1018

Warning

The plug-socket combination must be accessible at all times, because it serves as the main disconnecting device. Statement 1019

Warning

This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024

Warning

Class 1 LED product. Statement 1027

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030

Warning

Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040

Warning

When installing or replacing the unit, the ground connection must always be made first and disconnected last. Statement 1046

Warning

To prevent the system from overheating, do not operate it in an area that exceeds the maximum recommended ambient temperature of:
 <122°F (50°C).Statement 1047

Warning

Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments. Statement 1051

Warning

Invisible laser radiation may be emitted from the end of the unterminated fiber cable or connector. Do not view directly with optical instruments. Viewing the laser output with certain optical instruments (for example, eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard.

Statement 1056

Warning

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071

Warning

Voltages that present a shock hazard may exist on Power over Ethernet (PoE) circuits if interconnections are made using uninsulated exposed metal contacts, conductors, or terminals. Avoid using such interconnection methods, unless the exposed metal parts are located within a restricted access location and users and service people who are authorized within the restricted access location are made aware of the hazard. A restricted access area can be accessed only through the use of a special tool, lock and key or other means of security. Statement 1072

Warning

No user-serviceable parts inside. Do not open. Statement 1073

Warning

Installation of the equipment must comply with local and national electrical codes. Statement 1074

Warning

To prevent airflow restriction, allow clearance around the ventilation openings to be at least: 3 inches (7.6 cm). Statement 1076

Warning

Hot surface. Statement 1079

1

8-port or 16-port Cisco Catalyst 1000 switch

6

Screw template (47-100996-02)

2

AC power cord

7

(Optional) Console cable or USB cable

3

Four rubber mounting feet (51-0089)

8

(Optional) Power cord retainer

4

Compliance documentation (78-101287-01)

9

(Optional) Cable guard

5

Three number-8 screws (48-1689-01)

10

(Optional) DIN rail mount

1

Externally powered 8-port or 16-port Cisco Catalyst 1000 switch

8

(Optional) Power cord retainer

2

AC power cord

9

(Optional) Cable guard

3

Four rubber mounting feet (51-0089)

10

(Optional) DIN rail mount

4

Compliance documentation (78-101287-01)

11

Power Adaptor - PWR-ADPT-18W1

5

Three number-8 screws (48-1689-01)

12

Power Adaptor - PWR-ADPT-85W2

6

Screw template (47-100996-02)

13

Power Adaptor - PWR-ADPT-150W3

7

(Optional) Console cable or USB cable

Warning

Step 1

Locate the adhesive strip with the rubber feet in the accessory kit.

Step 2

Remove the four rubber feet from the adhesive strip, and attach them to the recessed areas at the bottom of the unit. This prevents the switch from sliding on the desk or shelf.

Step 3

Place the switch on the desk or shelf.

Step 1

Use the screw template to align the mounting screw holes and also as a guide to make sure that you install the screws into the desk or shelf with proper clearance.

Step 2

Position the screw template on top of the desk or shelf so that the edge that is marked as CABLE SIDE ENTRY faces the front of the desk or shelf. This ensures that the power cord faces the rear of the desk or shelf after the switch is installed.

Step 3

Peel the adhesive strip off the bottom of the screw template, and attach it to the top of the desk or shelf.

Step 4

Use a 0.144-inch (3.7 mm) or a #27 drill bit to drill a 1/2-inch (12.7 mm) hole in the two screw template slots.

Step 5

Insert two screws in the slots on the screw template, and tighten them until they touch the top of the screw template.

Step 6

Remove the screw template from the desk or shelf.

Step 7

Place the switch onto the mounting screws, and slide it forward until it locks in place.

Warning

Read the wall-mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system. Statement 378

Caution

Do not wall-mount the switch with its front panel facing up. Following safety regulations, wall-mount the switch with its front panel facing down or to the side to prevent airflow restriction and to provide easier access to the cables

Step 1

Locate the screw template. The template is used to align the mounting screw holes.

Step 2

Position the screw template so that the edge that is marked as CABLE SIDE ENTRY faces toward the floor.

Step 3

Peel the adhesive strip off the bottom of the screw template.

Step 4

Attach the screw template to the wall.

Step 5

Use a 0.144-inch (3.7 mm) or a #27 drill bit to drill a 1/2-inch (12.7 mm) hole in the two screw template slots.

Step 6

Insert two screws in the slots on the screw template, and tighten them until they touch the top of the screw template.

Step 7

Remove the screw template from the wall.

Step 8

Place the switch onto the mounting screws, and slide it down until it locks in place.

Warning

• This unit should be mounted at the bottom of the rack if it is the only unit in the rack.

• When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack.

• If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack.

Warning

To prevent airflow restriction, allow clearance around the ventilation openings to be at least: 3 in. (7.6 cm) Statement 1076

Step 1

Place the switch on the DIN rail mount.

Step 2

Use the two number-10 Phillips pan-head screws to secure the DIN rail mount to the switch.

Caution

Do not install the switch with its front panel facing up. Following safety regulations, install the switch with its front panel facing down, to allow sufficient airflow and to provide easier access to the cables.

Warning

To prevent airflow restriction, allow clearance around the ventilation openings to be at least: 3 in. (7.6 cm) Statement 1076

Step 1

Position the switch directly in front of the DIN rail, making sure that the top of the DIN rail mount clip hooks over the top of the DIN rail.

Step 2

Rotate the switch down toward the DIN rail until the release tabs on the DIN rail mount clicks.

Step 3

Lift lightly on the bottom of the switch to ensure that it is firmly locked in place.

Step 1

Ensure that power is removed from the switch, and disconnect all cables and connectors from the front panel of the switch.

Step 2

Pull down on the DIN rail mount release tabs. As the clips release, lift the bottom of the switch.

Note

This section applies to switches with an AC power connector.

Step 1

Choose the sleeve size of the power cord retainer based on the thickness of the cord. The smaller sleeve can be snapped off and used for thin cords.

Step 2

Slide the retainer around the AC power cord, and pass it around the loop on the switch.

Step 3

Slide the retainer through the first latch.

Step 4

Slide the retainer through the other latches to lock it.

Step 5

(Optional) Use the small sleeve for thin power cords. Use the small sleeve to provide greater stability for thin cords. Detach the sleeve, and slide it over the power cord.

Step 6

Secure the AC power cord by pressing on the retainer.

Note

You can use the cable guard when the switch is mounted on a desk, under a desk, or on a wall.

Step 1

(Optional) Attach the supplied washers before you install the cable guard.

Step 2

Use the supplied number-10 pan-head screws to attach the cable guard to the switch.

Step 3

Loosen the number-10 Phillips pan-head screws, slide the cable guide out, and pivot it upwards so that you can install the cables.

Step 4

Attach the cables to the switch.

Step 5

Guide the connected cables through the slots in the front of the cable guard. Slide the cable guide in as shown in the following figure. Tighten the screws.

Step 6

(Optional) To attach the cable guard to the desk or wall, use a 0.144-inch (3.7 mm) or a #27 drill bit to drill 1/2-inch (12.7 mm) holes at each of the two mounting locations. Insert the supplied 0.5 in. (12.7 mm) number-8 Phillips wood screws and tighten them.

Step 1

Attach an ESD-preventive wrist strap to your wrist and to a bare metal surface.

Step 2

Find the send (TX) and receive (RX) markings on the module top.

On some SFP modules, the send and receive (TX and RX) markings might be replaced by arrows that show the direction of the connection.

Step 3

If the module has a bale-clasp latch, move it to the open, unlocked position.

Step 4

Align the module in front of the slot opening, and push until you feel the connector snap into place.

Step 5

If the module has a bale-clasp latch, close it.

Step 6

For fiber-optic SFP modules, remove the dust plugs and save.

Step 7

Connect the SFP cables.

Step 1

Attach an ESD-preventive wrist strap to your wrist and to a bare metal surface.

Step 2

Disconnect the cable from the SFP module. For reattachment, note which cable connector plug is send (TX) and which is receive (RX).

Step 3

Insert a dust plug into the optical ports of the SFP module to keep the optical interfaces clean.

Step 4

If the module has a bale-clasp latch, pull the bale out and down to eject the module. If the latch is obstructed and you cannot use your finger, use a small, flat-blade screwdriver or other long, narrow instrument to open the latch.

Step 5

Grasp the SFP module, and carefully remove it from the module slot.

Step 6

Place the module in an antistatic bag or other protective environment.

Warning

Voltages that present a shock hazard may exist on Power over Ethernet (PoE) circuits if interconnections are made using uninsulated exposed metal contacts, conductors, or terminals. Avoid using such interconnection methods, unless the exposed metal parts are located within a restricted access location and users and service people who are authorized within the restricted access location are made aware of the hazard. A restricted access area can be accessed only through the use of a special tool, lock and key or other means of security. Statement 1072

Caution

Category 5e and Category 6 cables can store high levels of static electricity. Always ground the cables to a suitable and safe earth ground before connecting them to the switch or other devices.

Caution

Noncompliant cabling or powered devices can cause a PoE port fault. Use only standard-compliant cabling to connect Cisco prestandard IP Phones and wireless access points, IEEE 802.3af, or 802.3at (PoE+) compliant devices. You must remove any cable or device that causes a PoE fault.

Step 1

Connect one end of the cable to the switch PoE port.

Step 2

Connect the other end of the cable to an RJ-45 connector on the other device. The port LED turns on when both devices have established link.

The port LED is amber while STP discovers the topology and searches for loops. This process takes about 30 seconds, and then the port LED turns green. If the LED is off, the other device might not be turned on, there might be a cable problem, or there might be a problem with the adapter in the other device.

Step 3

Reconfigure and reboot the connected device, if needed.

Step 4

Repeat Steps 1 through 3 to connect each device.

Switch to switch

Yes

No

Switch to hub

Yes

No

Switch to computer or server

No

Yes

Switch to router

No

Yes

Switch to IP phone

No

Yes