Corner Chamfering, (G39) - Fagor CNC 8070 Programming Manual

× Bookmark added × Added to my manuals

1. Manuals
2. Brands
3. Fagor Manuals
4. Controller
5. CNC 8070
6. Programming manual

Corner Chamfering, (G39) - Fagor CNC 8070 Programming Manual Hide thumbs Also See for CNC 8070:

• Operating manual (414 pages)
,
• Hardware configuration (276 pages)
,
• Manual (164 pages)

1 2 3 4 5 6 Table Of Contents 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 475 476 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556

• page of 556 Go / 556
• Contents
• Table of Contents
• Bookmarks

Table of Contents

Advertisement

Programming manual 7.5 7. 144 CNC 8070 (S V02.0 ) OFT X 132

Corner chamfering, (G39)

Function G39 may be used to insert a chamfer of a particular size without having to calculate the intersection points. Programming The chamfer definition must be programmed between the two paths that define the corner to be chamfered. These paths may be linear and/or circular. The programming format is "G39 I<size>", where the size value is programmed in millimeters or in inches, depending on which are the active units. G01 G90 X25 Y60 G39 I5 G01 X40 Y0 Considerations The "I" value of the chamfer size remains active until another value is programmed, therefore, it won't be necessary to program it in successive chamfering operations of the same size. The "I" value of the chamfer size is also used by functions: G36 (Corner rounding) as rounding radius. G37 (Tangential entry) as entry radius. G38 (Tangential exit) as exit radius. This means that the chamfer size set in G39 will be the new value of the entry radius, exit radius or rounding radius when programming one of these functions or vice versa. N10 G01 X10 Y10 F600 N20 G01 X10 Y50 N30 G36 I5 N40 G01 X50 Y50 N50 G36 N60 G01 X50 Y10 N70 G39 N80 G01 X90 Y10 G03 G90 X40 Y50 I0 J30 G39 I5 G01 X40 Y0 (Rounding. Radius=5) (Rounding. Radius=5) (Chamfer. Size=5) Table of Contents Previous Page Next Page

• 1
• ...
• 165
• 166
• 167
• 168

Show Quick Links

• Quick Links:
• Program Structure
• G83. Deep-Hole Drilling Canned Cycle with...

Hide quick links:

Permanently Temporary Cancel

Advertisement

Table of Contents

Related Manuals for Fagor CNC 8070

• Power Tool Fagor CNC 8060 Installation Manual (698 pages)
• Control Unit Fagor CNC 8070 Operating Manual (414 pages)
• Control Panel Fagor CNC 8070 Operating Manual (358 pages)
• Control Systems Fagor CNC 8070 Hardware Configuration (276 pages)
• Control Systems Fagor CNC 8070 Hardware Configuration (212 pages)
• Control Unit Fagor CNC 8070 Series Manual Remote modules (164 pages)
• Control Panel FAGOR CNC 8070 Manual Examples manual (102 pages)
• Control Systems Fagor CNC 8070 Hardware Configuration (100 pages)

• Control Unit Fagor CNC 8070 Quick Reference (44 pages)
• Control Systems Fagor CNC 8070 Original Instructions Manual (10 pages)
• Controller Fagor CNC 8060 Installation Manual (900 pages)
• Controller Fagor CNC 8055 Manual (12 pages)
• Controller Fagor CNC 8055 Manual (166 pages)
• Controller Fagor CNC 8055i FL EN Installation Manual Cnc 8055 series (732 pages)
• Controller Fagor 8055i CNC Handbook (12 pages)
• Controller Fagor 8055i FL EN Operating Manual Cnc 8055 series; cnc 8055i series; (210 pages)

Related Content for Fagor CNC 8070