| YOU HERE: Alloy Standards -> Copper - all grades OR Alloy Standards -> / EN 13601 / EN 13600 / EN 1976 / EN 13599 / EN 13605 / EN 13148 |
Cu-PHC ( CW020A )
| Grade : | Cu-PHC |
| Number: | CW020A |
| Classification: | Phosphorus-containing copper grade |
| Density | 8.9 g/cm ³ |
| Standard: | EN 13601: 2002 Copper and copper alloys. Copper rod, bar and wire for general electrical purposesEN 13600: 2002 Copper and copper alloys. Seamless copper tubes for electrical purposesEN 1976: 1998 Copper and copper alloys. Cast unwrought copper productsEN 13599: 2002 Copper and copper alloys. Copper plate, sheet and strip for electrical purposesEN 13605: 2002 Copper and copper alloys. Copper profiles and profiled wire for electrical purposesEN 13148: 2001 Copper and copper alloys. Hot-dip tinned strip |
| Equivalent grades: | Go here |
Chemical composition % of grade Cu-PHC ( CW020A )
| P | Cu | Pb | Bi | Others |
| 0.001 - 0.006 | min 99.95 | max 0.005 | max 0.0005 | total 0.03 |
Mechanical properties of grade Cu-PHC ( CW020A )
|
| Rm - Tensile strength (MPa) (R220) | 220-260 |
|
| Rm - Tensile strength (MPa) (R290) | 290-360 |
|
| Rm - Tensile strength (MPa) (R350) | 350 |
|
| Rp0.2 0.2% proof strength (MPa) (R220) | 140 |
|
| Rp0.2 0.2% proof strength (MPa) (R290) | 250 |
|
| Rp0.2 0.2% proof strength (MPa) (R350) | 320 |
|
| A - Min. elongation at fracture (%) (R350) | 5 |
|
| A - Min. elongation Lo = 50mm (%) (R220) | 33 |
|
| A - Min. elongation Lo = 50mm (%) (R290) | 4 |
|
| A - Min. elongation Lo = 100mm (%) (R350) | 3 |
| Vickers hardness ( HV): (H040) (R220) | 40 - 65 |
| Vickers hardness ( HV): (H090) (R290) | 90 - 110 |
| Brinell hardness (HB): (H100) (R350) | 100 |
Properties Cu-PHC
| Volume resistivity = 0.01724 - 0.01786 Ω*mm²/m ; |
Equivalent grades of grade Cu-PHC ( CW020A )Warning! Only for reference
| EU EN | GermanyDIN,WNr |
| Cu-PHC | |
Casting process
| GS | Sand casting |
| GM | Permanent mould casting |
| GZ | Centrifugal casting |
| GC | Continuous casting |
| GP | Pressure die casting |
Material conditions
| R | Material condition designated by the minimum value of tensile strength requirement for the product with mandatory tensile strength and elongation requirements |
| H | Material condition designated by the minimum value of hardness requirement for the product with mandatory hardness requirements |
Mechanical properties
| ReH | Minimum yield strength / Mindestwert der oberen Streckgrenze / Limite d elasticite minimale |
| Rm | Tensile strength / Zugfestigkeit / Resistance a la traction |
| A | Minimum elongation / Mindestwert der Bruchdehnung / Allongement minimal |
| J | Notch impact test / Kerbschlagbiegeversuch / Essai de flexion par choc |
| Cu-PHC ( CW020A ) Phosphorus-containing copper grade Chemical composition. Equivalents of Cu-PHC ( CW020A ). Standards.1 Mechanical Properties. Hardness |
| European Steel and Alloy Grades / Numbers Searchable Database © 2011- 2025 All rights reserved. About us. Contacts. The contents from this Steel & Alloy Database may not be reproduced. The entire risk as to use of these content is assumed by you the user |
