Flexmaster Joints Conveying Products - PDF Free Download

Transcription

1 Flexmaster Joints Conveying Products

2

3 Features Flexmaster Joints in Standard and Self-restrained Configurations Standard Features 1. Gasket provides compression seal when tightened against tube or pipe. 2. Hinged coupling provides for quick, easy assembly. 3. Bulged sleeve allows for ±4º angular misalignment. All gasket materials listed on page 4 are available in the standard style, increasing the number of suitable applications. Self-Restrained Features 1. Gasket provides compression seal when tightened against tube or pipe. 2. Hinged coupling provides for quick, easy assembly. 3. Bulged sleeve allows for ±4º angular misalignment. 4. Notched channel ring which grips pipe firmly to restrict movement along pipe or tubing. Gasket materials available include the C (Buna-N) and D (EPDM) compounds. Flexmaster joints are available in both standard and selfrestrained styles. The self-restrained style has a stainless steel gripping ring inside each gasket. This feature allows the joint to maintain a firm grip on the pipe or tube, preventing movement along the pipe or tube. The bulged, straight-through Flexmaster joints accommodate angular misalignment up to ±4º per end. Tees, elbows, and crosses accommodate angular misalignment up to ±2 o per end. See pages 10 thru 17 for the angular misalignment allowed on each specific part. Flexmaster joints are designed for up to 300 psi (2.07 MPa) service, depending on application and size. Refer to pressure ratings on page 4. Flexmaster joints absorb vibration and are ideal for making quick connections and disconnections when repairing or disassembling a system. They can be furnished with several types of gasket compounds and sleeve materials, including stainless steel for marine and corrosive applications. Flexmaster joints are currently in use in thousands of applications throughout the world. For typical Flexmaster joint applications see photos on page 2. II

4 Features Save Time - Make Pipe And Tube Connection Easier Used on Plain End Tube or Pipe No threading, flanging, welding, grooving or other special end preparation of tube or pipe is required. Use pipe after it is cut to appropriate lengths. The Flexmaster joint will accommodate large tolerances in the length of the gap. See Table 1, page 9 for insertion depth tolerances. Absorbs Vibration Pipe vibration and noise can be drastically reduced with Flexmaster joints. The resilient, thick rubber of the Flexmaster joint gasket absorbs vibration and noise. Use of the self-restrained style restricts movement along vibrating pipes and tubes. Even Misaligned Piping is No Problem The Flexmaster joint design eliminates flanged bolt holes and pipe threads that require careful alignment. The Flexmaster bulged joint permits up to a total of ±4º angular installation misalignment at each end while maintaining a leakproof seal. Easy to Install Installation time can be slashed by using Flexmaster joints. Basic assembly tools are all that s needed. After extensive use, the gaskets can be replaced easily and quickly. See page 8 for complete assembly instructions.

5 Applications Flexmaster joint elbows on a large hydraulic power system, which connect pipe from pumps to hydraulic fluid reservoirs. Flexmaster joints join water lines on a huge diesel engine. A number of Flexmaster joints are installed on this compressor to connect water and oil lines, providing quick, easy connection and protection against vibration. A large dry-cleaning plant uses Flexmaster joints to connect piping at elbow junctures. Flexmaster joints are used to join piping on air compressors.

6 Specials Made to Order Special Configurations and Seal Materials Can Be Ordered Flexmaster joints can be produced with various configurations and terminal end designs. A few of the special Flexmaster joint configurations which have been manufactured by Eaton are displayed above. Please consult Eaton when ordering specials. Manufacturing Engineering Flexmaster joints are manufactured by highly experienced and trained individuals who are dedicated solely to the production and packaging of Flexmaster joints. The Flexmaster joints manufacturing team is backed by the strong technical support from Eaton s engineering staff.

7 Technical Data Gasket Temperature Ratings C BUNA-N water -25º F. to +180º F. (Standard) (-32º C. to +82º C.) oils -25º F. to +212º F. (-32º C. to +100º C.) V -25º F. to +450º F. Fluorocarbon (-32º C. to +232º C.) S -65º F. to +350º F. Silicone (-54º C. to +177º C.) D water and +20º F. to +275º F. EPDM water/glycol (+29º C. to +137º C.) mixture N BUNA-N water and -25º F. to +225º F. (High temp.) steam (-32º C. to +107º C.) oils -25º F. to +250º F. (-32º C. to +121º C.) Maximum temperature ratings are meant as a guide only. For extreme temperature conditions, consult factory. Pressure Ratings Size Range Standard Self-Restrained Pipe Tube Gasket Gasket 3 /8-3 /4 1 /2-1 3 /8 300 psi 300 psi (2.07 MPa) (2.07 MPa) /2-2 1 /2 200 psi 200 psi (1.38 MPa) (1.38 MPa) 2 1 / psi 150 psi (1.03 MPa) (1.03 MPa) Warning: The Flexmaster joint is designed to seal pipe and tube connections. The Flexmaster joint is not intended to hold piping systems together. Normal hangers, guides, anchors and other external piping restraints must be used to restrain the piping or tubing system from movement. Pipe and tube materials which can be connected by Flexmaster joints* Pipe or Tube Standard Self-Restrained Material Gasket Gasket** Carbon Steel X X Stainless Steel X X Aluminum X Not Recommended P.V.C. (Plastic) X Not Recommended Copper X Not Recommended Vacuum Ratings Size Range Standard Self-Restrained Pipe Tube Gasket Gasket All sizes All sizes 25 in. Hg. 25 in. Hg bar 1.79 bar NOTE: º F., inches, in. Hg., psi in bold º C., mm, bar, MPa in light * All piping and tubing connected by Flexmaster joints must meet the nominal O.D. dimensions presented on pages ** Piping and Tubing, which use self-restrained gaskets, must have a hardness between on a Rockwell B scale (45-85 Rb). Eaton Gasket Indentifier Chart Gasket Gasket Gasket Identifying Designation Compound Color Color Patch C Buna N (std) Black Yellow or White N Buna N (high temp) Black Rust Orange D EPDM Black Dark Blue V Fluorocarbon Black Light Green S Silicone Rust Orange None

8 Technical Data Gasket Selector Chart Gasket Material: C BUNA-N (standard) D EPDM N BUNA-N (high temperature) V Fluorocarbon S Silicone Key: G GOOD F FAIR Not Recommended An important consideration in the selection of a gasket material is to avoid undesirable chemical reaction between the agent carried and the gasket material. The gasket selector chart indicates the compound most serviceable in specific agents. FLUID Gasket Material D C/N V S Acetic Acid (concentrated) RT F F G F Acetic Acid (dilute) RT (to 10%) F F G G Acetic Acid Vapors F F F F Acedit Anhydride - F - F Acetone G - - F Acetylene G G G F Air G G G G Air (Hot) 215º G F G G Alcohols, Aliphatic G F G G Alcohols, Aromatic F - F F Alkaline Solutions (Hydroxides) F G F G Aluminum Salt solutions G G G G Ammonia Gas (Cold) G G - - Ammonia, Liquid (Anhydrous) G G - F Ammonia Aqueous G F - G Ammonium Salt Solutions G G F F Aniline Dyes F - G F Aniline Oils F - F F Asphalt - - G - Benzine (Gasoline) - G G - Bromine - - G - Butylene - F G - Calcium Hypochlorite (no free Chlorine) G - G F Calcium Salt solutions G G G F Carbolic Acid (Phenol) RT or Hot F - G - Carbon Dioxide (Dry) G G F F Carbonic Acid G F G G Carbon Disulphide RT - - G - Carbon Tetrachloride RT - - G - Chlorinated Solvents - - G G Chlorine (Dry) - - G - Chlorine (wet or solutions) F - G - Cottonseed Oil G G G G Creosote (wood or coal tar) - G G - Chromic Acid 50% - F G - Citric Acid G G G G Copper Salt Solutions G F G G Diesel Fuel - G G - Ethers RT F F G - Ethylene Glycol G G G G Ethylene Dichloride - - G G Ferric Salt Solutions G G G G Ferrous Salt Solutions G G G G Formaldehyde RT F - - G Fuel Oil - G F - Furfural G Freon 12 (Refrigerant) G G G - Freon 13 (Refrigerant) F G G - Gasoline (Sour or refined) - G G - Glycerin (Glycerol) G G G G Heptane - G G - Hexane - G G - FLUID Gasket Material D C/N V S Hydraulic Oils - G G - Straight Petroleum Base Water Petroleum Emulsion - G G F Water Glycol G G G F Straight Phosphate Ester G - F F Phosphate Ester/Petroleum Blend - - F - Ester Blend G G F F Silicone Oils G G G - Hydrochloric Acid RT G F G - Hydrofluoric Acid (48% sol) RT - - G - Hydrolube G G G F Hydrogen Peroxide (dilute) F F G G Hydrogen Peroxide (concentrated) - - F F Hydrogen Sulfide (dry) RT F F - - Hydrogen Sulfide (wet) RT F - G - Hypochlorite Solutions G F G F (no free Chlorine) Kerosene RT - G G - Linseed Oil - G G - Lube Oil (Mineral) - G G - Lubricating Oils (Diester Base) - F G - Magnesium Salt Solutions G G G G Mercuric Chloride G G G - Mercury G G G F Mineral Oil - G G G Naphtha - F G - Napthalene - - G - Nitric Acid (less than 20%) F - G - Oleic Acid - G F - Oxalic Acid G F G F Oxygen, Gaseous G F G G Paraffin - G G F Petroleum Oils (Sour or Refined) - G G - Phosphoric Acid (Commercial) G - G - Potassium Salt Solutions G G G G Pydraul C Series, F F - G F Pydraul F Series G Sodium Salt solutions G G G F Steam F Sulfur G Sulfur Dioxide (wet or dry) G - - F Sulfuric Acid (10-75%) F - G - Sulfuric Acid (75-95%) - - G - Sulfuric Acid (95%) RT - - G - Sulfurous Acid - F G - Tannic Acid F G F F Trichlorethylene - - G - Turpentine - F G - Vegetable Oils G G G G Water (fresh or salt) cold G G G G Water (fresh or salt) hot G!! G º F. max. Xylene - - G - Zinc Salt Solutions G G G G!! C maximum +180º F., N maximum +225º F. 5

9 How To Order Standard (Un-Restrained) Style Self-Restrained Style NH16XX ( ) 000 ( ) 000 Basic Part Number (from pages 10-17) Example: NH1600 Gasket Material: C = BUNA-N (standard) D = EPDM *N = BUNA-N (high temperature) *S = Silicone *V = Fluorocarbon * Available in Standard (Un-Restrained) Model Only. Example Part Number: NH1600C075B0250 Complete assemblies may be ordered by the procedure shown above. Standard components may be ordered as shown on page 7. Joint Length (in thousands of inch). Example: 2.5 = 0250 Style is available in lengths shown. Other lengths are available in multiples of 1-inch on special requests. Contact Eaton for availability. Sleeve Material: B = Plated Steel (Standard) S = Stainless Steel (Sleeve onlyconsult Eaton for availability) Size of Pipe or Tube to be connected (in hundredths of inch) Example:.75 = 075

10 Technical Data Parts List STRAIGHT GASKET coupling SLEEVES retainer GASKETS Gasket Material: C BUNA-N (standard) D EPDM N BUNA-N (high temperature) V Fluorocarbon S Silicone (Other materials available. Consult Eaton.) Tube Tube Includes Material Available Material Available size O.D. Nut & Bolt from Stock Self Restrained from Stock (inches) (inches) Standard Standard Standard Standard Gasket C D N S V Gasket C D* NH YF NK B0250 NK NK X100 X X X X X NK X100 X X NH YF NK B0288 NK NK X125 X X X X X NK X125 X X NH YF NK B0300 NK NK X138 X X X X NH YF NK B0300 NK NK X150 X X X X X NK X150 X X NH YF NK B0350 NK NK X175 X X X - - NK X175 X X NH YF NK B0350 NK NK X200 X X X X X NK X200 X X NH YF NK B0400 NK NK X225 X X X NH YF NK B0400 NK NK X250 X X X X X NK X250 X X NH YF NK B0650 NK NK X250 X X X X X NK X250 X X NH YF NK B0500 NK NK X300 X X X X X NK X300 X X NH YF NK B0650 NK NK X325 X X X NH YF NK B0650 NK NK X300 X X X X X NK X300 X X NH YF NK B0650 NK NK X350 X X X X X NK X350 X X NH YF NK B0650 NK NK X400 X X X X X NK X400 X X NH YF NK B0650 NK NK X500 X X X - - NK X500 X X Pipe Pipe Size O.D. (inches) (inches) NH YF NK B0200 NK NK X038 X X X NH YF NK B0225 NK NK X050 X X X X X NK X050 X X NH YF NK B0250 NK NK X075 X X X X X NK X075 X X NH YF NK B0288 NK NK X100 X X X X X NK X100 X X NH YF NK B0325 NK NK X125 X X X X X NK X125 X X NH YF NK B0350 NK NK X150 X X X X X NK X150 X X NH YF NK B0400 NK NK X200 X X X X X NK X200 X X NH YF NK B0650 NK NK X250 X X X X X NK X250 X X NH YF NK B0650 NK NK X300 X X X X X NK X300 X X NH YF NK1237-B NK NK X350 X X X X X NK X350 X X NH YF NK B0650 NK NK X400 X X X X X NK X400 X X NH YF NK B0650 NK NK X500 X X X - X NK X500 X X NH YF NK B0650 NK NK X600 X X X X X NK X600 X X Bolt Part Numbers JOINT SIZE BOLT NUT (inches) PART NUMBER PART NUMBER Tube Pipe Carbon Steel Carbon Steel.50 to to A A4C-C 1.25 to to A A5C-C 2.75 to to A A6C-C 6 5 to A A8C-C 7

11 Assembly Instructions Pipe and Tubing Preparation and Flexmaster Joint Installation Instructions 1. Pipe (Tube) End Preparation Deburr and clean pipe (tube) ends. Surface should be free of deep scratches, gouges, dents, dirt, etc. 2. Joint Installation Install retainer (1), gasket* (2) and sleeve (3) on one side of pipe in sequence shown in Figure 1. Install remaining retainer (4) and gasket (5) on other pipe end. Position retainer (4) and gasket (5) to proper pipe insertion depth ( D ) as shown in Table 1. Slide sleeve (3) to gasket (5) and move gasket (2) and retainer (1) into position as shown in Figure 2. Pipe must be inserted to proper depth ( D ) into both gaskets as shown in Table 1. *3. Special Notes Assembly of gaskets can be made easier by dipping gaskets in water or the fluid to be sealed. The use of other rubber lubricants can be detrimental to the life of the gaskets. Never lubricate the metal parts. Self-restrained gasket installation. To simplify installation of a selfrestrained gasket, install lower gasket halfway onto the pipe first, leaving the split area in the steel retaining ring free at the top. See Figure 3. Then, stretch the gasket and split area of the retaining ring until they slip over the tube or pipe and into position. Refer to Figure Coupler Installation Install both V-couplings, encompassing the retainer, gasket and sleeve as shown in Figure 4. Do not tighten either coupling until the entire joint is assembled (See Figure 2). Tighten nuts to the torque specified in Table 2. Do NOT lubricate the nut or bolt before assembly. The gap method outline in Table 3 may be used for standard gaskets only. Figure 4 Figure 1 Figure 2 Figure 3 WARNING Maximum temperature ratings are meant as a guide only. For extreme temperature conditions, consult factory. Improper installation, use or selection of the Flexmaster joints can result in personal injury, property damage or death.

12 Technical Data Table 1. Required insertion depth* of pipe and tube Pipe Tube Pipe D D Tube D D Size min. max. Size min. max *Dimensions shown are for standard, straight, bulged sleeves only. Elbow, tees and specials must meet the minimum insertion depths. NOTE: inches and inch-lbs in bold, mm and N m in light. Table 2. Flexmaster joint assembly tightening guide. Torque Method of installation** Size Standard Self-Restrained.75 to 1.12 Tube inch-lbs inch-lbs. (19.1 to 28.4 mm) ( N m) ( N m).38 to.75 Pipe 1.25 to 2.75 Tube inch-lbs inch-lbs. (31.8 to 69.9 mm) ( N m) ( N m) 1 to 2 Pipe 2.88 to 3.50 Tube inch-lbs inch-lbs. (73 to 88.9 mm) ( N m) ( N m) 2.50 to 3 Pipe 4 to 5 Tube inch-lbs inch-lbs. (101.6 to 127 mm) ( N m) ( N m) 3.50 to 4 Pipe 6 Tube inch-lbs inch-lbs. (152.4 mm) ( N m) ( N m) 5 to 6 Pipe **Note: the torque values specified are for an un-lubricated (dry) nut and bolt. Table 3. Optional Clearance Method for Installation of Standard Gaskets. (Self-restrained gaskets must be installed by Torque Method.) Dimension X ±.06 Tube Size Pipe Size ,.63,.75 3 /8, 1 / , 16.0, , / , , , , / , / , / , , , / , , 6 Use Torque 127, Method

13 Joints for Rigid Pipe Basic Part Number: NH1600 NH1650 Allowable misalignment: ±4º per end Pipe Pipe Straight Size O.D. B C Part Number* A **NH1600X038X NH1600X050X NH1650X050X NH1600X075X NH1650X075X NH1600X100X NH1650X100X NH1600X125X NH1650X125X NH1600X150X NH1650X150X NH1600X200X NH1650X200X NH1600X250X NH1650X250X NH1600X300X NH1650X300X NH1600X350X NH1650X350X NH1600X400X NH1650X400X **NH1600X500X NH1650X500X **NH1600X600X NH1650X600X Note: Letter X in part numbers shown indicates a code letter to be filled in. See Page 6 for explanation of part numbers and how to order. * Gray part numbers are standard type. Black part numbers are self-restrained type. ** Sleeve in this size is cylindrical (no-bulge). Allowable misalignment is ±2º per end for this size. Dimensions: inches in bold, mm in light 10

14 Joints for Rigid Pipe Basic Part Number: NH1600 (Long) Basic Part Number: NH1601 NH1650 (Long) NH1651 Allowable misalignment: ±4º per end Allowable misalignment: ±2º per end Straight Pipe PIPE double-bulged 45º Long Elbow Size O.D. Part Number* E Part Number* l r **NH1600X038X NH1601X038X NH1600X050X NH1601X050X NH1650X050X NH1651X050X NH1600X075X NH1601X075X NH1650X075X NH1651X075X NH1600X100X NH1601X100X NH1650X100X NH1651X100X NH1600X125X NH1601X125X NH1650X125X NH1651X125X NH1600X150X NH1601X150X NH1650X150X NH1651X150X NH1600X200X NH1601X200X NH1650X200X NH1651X200X NH1600X250X NH1601X250X NH1650X250X NH1651X250X NH1600X300X NH1601X300X NH1650X300X NH1651X300X NH1600X350X NH1601X350X NH1650X350X NH1651X350X NH1600X400X NH1601X400X NH1650X400X NH1651X400X NH1600X500X NH1650X500X NH1600X600X NH1650X500X Note: Letter X in part numbers shown indicates a code letter to be filled in. See Page 6 for explanation of part numbers and how to order. *Gray part numbers are standard type. Black part numbers are self-restrained type. ** Sleeve in this size is cylindical (no-bulge). Allowable misalignment is ± 2º per end for this size. Straight, Double-Bulged joints are available in longer lengths than E shown in increments of 1 inch. Consult Eaton. E dimension is minimum length for longer joints Dimensions: inches in bold, mm in light. 11

15 Joints for Rigid Pipe Basic part number: NH1617 Basic Part Number: NH1602 Basic Part Number: NH1618 NH1667 NH1652 NH1668 Allowable misalignment: ±2º per end Allowable misalignment: ±2º per end Allowable misalignment: ±2º per end Pipe 45º Short Elbow 90º Long Elbow 90º Short Elbow Size Part Number* l Part Number* l r Part Number* L D.38 NH1617X038X 2.56 NH1602X038X NH1618X038X NH1617X050X 2.99 NH1602X050X NH1618X050X NH1667X050X 75.9 NH1652X050X NH1668X050X NH1617X075X 3.41 NH1602X075X NH1618X075X NH1667X075X 86.6 NH1652X075X NH1668X075X NH1617X100X 3.89 NH1602X100X NH1618X100X NH1667X100X 98.8 NH1652X100X NH1668X100X NH1617X125X 4.42 NH1602X125X NH1618X125X NH1667X125X NH1652X125X NH1668X125X NH1617X150X 4.85 NH1602X150X NH1618X150X NH1667X150X NH1652X150X NH1668X150X NH1617X200X 5.55 NH1602X200X NH1618X200X NH1667X200X NH1652X200X NH1668X200X NH1617X250X 5.97 NH1602X250X NH1618X250X NH1667X250X NH1652X250X NH1668X250X NH1617X300X 6.40 NH1602X300X NH1618X300X NH1667X300X NH1652X300X NH1668X300X NH1617X350X 6.83 NH1602X350X NH1618X350X NH1667X350X NH1652X350X NH1668X350X NH1617X400X 7.26 NH1602X400X NH1618X400X NH1667X400X NH1652X400X NH1668X400X Note: Letter X in part numbers shown indicates a code letter to be filled in. See Page 6 for explanation of part numbers and how to order. *Gray part numbers are standard type. Black part numbers are self-restrained type. Dimensions: inches in bold, mm in light 12

16 Joints for Rigid Pipe Basic Part Number: NH1604 Basic Part Number NH1606 NH1654 NH1656 Allowable misalignment: ±2º per end Allowable misalignment: ±2º per end Pipe TEE bulkhead Joint MIN. Size Part Number* l E Part Number* l.38 NH1604X038X NH1606X038X NH1604X050X NH1606X050X 1.75 NH1654X050X NH1656X050X NH1604X075X NH1606X075X 2.25 NH1654X075X NH1656X075X NH1604X100X NH1606X100X 2.50 NH1654X100X NH1656X100X NH1604X125X NH1606X125X 2.62 NH1654X125X NH1656X125X NH1604X150X NH1606X150X 2.88 NH1654X150X NH1656X150X NH1604X200X NH1606X200X 3.38 NH1654X200X NH1656X200X NH1604X250X NH1606X250X 4.00 NH1654X250X NH1656X250X NH1604X300X NH1606X300X 4.00 NH1654X300X NH1656X300X NH1604X350X NH1606X350X 4.00 NH1654X350X NH1656X350X NH1604X400X NH1606X400X 4.00 NH1654X400X NH1656X400X Note: Letter X in part numbers shown indicates a code letter to be filled in. See Page 6 for explanation of part numbers and how to order. *Gray part numbers are standard type. Black part numbers are self-restrained type. Dimensions: inches in bold, mm in light 13

17 Joints for Inch-Size Tube Basic part number: NH1625 Basic Part Number NH1625 (Long) NH1675 NH1675 (Long Allowable misalignment: ±4º per end Allowable misalignment: ±2º per end Straight Tube StraighT double-bulged SizE b c Part Number* A Part Number* E NH1625X075X NH1625X075X NH1625X088X NH1625X088X NH1625X100X NH1625X100X NH1675X100X NH1675X100X NH1625X112X NH1625X112X NH1625X125X NH1625X125X NH1675X125X NH1675X125X NH1625X138X NH1625X138X NH1675X138X NH1675X138X NH1625X150X NH1625X150X NH1675X150X NH1675X150X NH1625X175X NH1625X175X NH1675X175X NH1675X175X NH1625X200X NH1625X200X NH1675X200X NH1675X200X NH1625X225X NH1625X225X NH1600X200X NH1600X200X NH1650X200X NH1650X200X NH1625X250X NH1625X250X NH1675X250X NH1675X250X NH1625X275X NH1625X275X NH1600X250X NH1600X250X NH1650X250X NH1650X250X NH1625X300X NH1625X300X NH1675X300X NH1675X300X NH1625X325X NH1625X325X NH1600X300X NH1600X300X NH1650X300X NH1650X300X NH1600X350X NH1600X350X NH1650X350X NH1650X350X NH1600X400X NH1600X400X NH1650X400X NH1650X400X **NH1625X500X **NH1625X500X NH1675X500X NH1675X500X Note: Letter X in part numbers shown indicates a code letter to be filled in. See Page 6 for explanation of part numbers and how to order. *Gray part numbers are standard type. Black part numbers are self-restrained type. Dimensions: inches in bold, mm in light **Sleeve in this size is cylindrical (unbulged). Allowable misalignment for this size is ±2º per end. Straight, Double-Bulged joints are available in longer lengths than E shown in increments of 1 inch. E dimension is minimum length for longer joints. 14

18 Joints for Inch-Size Tube Basic part number: NH1631 Basic Part Number NH1626 (Long) NH1681 NH1676 (Long Allowable misalignment: ±2º per end Allowable misalignment: ±2º per end Tube Bulkhead Joint Min. 45º Elbow Size Part Number* l Part Number* l r NH1631X100X 2.25 NH1626X100X NH1681X100X 57.2 NH1676X100X NH1631X125X 2.50 NH1626X125X NH1681X125X 6.35 NH1676X125X NH1631X138X 2.62 NH1626X138X NH1681X138X 6.65 NH1676X138X NH1631X150X 2.62 NH1626X150X NH1681X150X 6.65 NH1676X150X NH1631X200X 2.88 NH1626X200X NH1681X200X 73.2 NH1676X200X NH1631X250X 3.38 NH1626X250X NH1681X250X 85.9 NH1676X250X NH1631X300X 4.00 NH1626X300X NH1681X300X NH1676X300X NH1606X300X 4.00 NH1601X300X NH1656X300X NH1651X300X NH1606X350X 4.00 NH1601X350X NH1656X350X NH1651X350X NH1606X400X 4.00 NH1601X400X NH1656X400X NH1651X400X NH1631X500X NH1681X500X Dimensions: inches in bold, mm in light Note: Letter X in part numbers shown indicates a code letter to be filled in. See Page 6 for explanation of part numbers and how to order. *Gray part numbers are standard type. Black part numbers are self-restrained type. 15

19 Joints for Inch-Size Tube Basic part number: NH1627 Basic Part Number NH1635 NH1677 NH1685 Allowable misalignment: ±2º per end Allowable misalignment: ±2º per end SAE Tube 90º Elbow Flange Straight Size Part Number* l r head Size Part Number* l.75 NH1627X075X NH1627X100X NH1635X NH1677X100X NH1685X NH1635X NH1685X NH1627X125X NH1635X NH1677X125X NH1685X NH1635X NH1685X NH1627X138X NH1635X NH1677X138X NH1685X NH1627X150X NH1635X NH1677X150X NH1685X NH1635X NH1685X NH1627X175X NH1677X175X NH1627X200X NH1635X NH1677X200X NH1685X NH1635X NH1685X NH1627X250X NH1635X NH1677X250X NH1685X NH1635X NH1685X NH1627X300X NH1635X NH1677X300X NH1685X NH1627X350X NH1677X350X NH1627X400X NH1635X NH1677X400X NH1685X NH1627X450X NH1677X450X Dimensions: inches in bold, mm in light Note: Letter X in part numbers shown indicates a code letter to be filled in. See Page 6 for explanation of part numbers and how to order. *Gray part numbers are standard type. Black part numbers are self-restrained type. Flexmaster flanged and threaded styles shown on this page are not normally stock items and are not available in stainless steel. Consult Eaton for delivery. 16

20 Joints for Inch-Size Tube Basic part number: NH1637 Basic Part Number NH1641 NH1687 NH1691 Allowable misalignment: ±2º per end Allowable misalignment: ±2º per end Tube 90º Elbow Thread Straight Size Part Number* l j r NPTF Part Number* L 1.00 NH1637X /2 NH1641X NH1687X NH1691X NH1637X NH1687X NH1637X /4-11 1/2 NH1641X NH1687X NH1691X NH1637X NH1687X NH1637X /2-11 1/2 NH1641X NH1687X NH1691X NH1637X NH1687X NH1637X NH1641X NH1687X NH1691X NH1637X NH1687X NH1637X /2-8 NH1641X NH1687X NH1691X NH1637X NH1687X NH1637X NH1687X NH1637X NH1687X Dimensions: inches in bold, mm in light Note: Letter X in part numbers shown indicates a code letter to be filled in. See Page 6 for explanation of part numbers and how to order. *Gray part numbers are standard type. Black part numbers are self-restrained type. Flexmaster flanged and threaded styles shown on this page are not normally stock items and are not available in stainless steel. Consult Eaton for delivery. 17

21 Eaton Lone Oak Road Eden Prairie, MN USA Tel: Fax: Eaton 20 Rosamond Road Footscray Victoria 3011 Australia Tel: (61) Fax: (61) Eaton Dr.-Reckeweg-Str. 1 D Baden-Baden Germany Tel: (49) Fax: (49) Eaton Corporation All Rights Reserved Printed in USA Document No. E-MEFL-MR001-E2 Supersedes E-MEFL-MR001-E1 January 2008