For Loop - VHDL & Verilog Example - Nandland

For Loop – VHDL and Verilog Example

Write synthesizable and testbench For Loops

For loops are one of the most misunderstood parts of any HDL code. For loops can be used in both synthesizable and non-synthesizable code. However for loops perform differently in a software language like C than they do in VHDL. You must clearly understand how for loops work before using them!

Converting A Software-Style For Loop to VHDL/Verilog

For loops are an area that new hardware developers struggle with. You have likely seen for loops dozens of times in C, so you think that they are the same in Verilog and VHDL. Let me be clear here: For loops do not behave the same way in hardware as in software.

For loops in synthesizable code are used to expand replicated logic. They are simply a way of shrinking the amount of code that is written by the hardware designer. Again, until you understand how exactly this expansion of replicated logic works, do not use for loops. Instead think about how you want your code to behave and figure out a way to write it in C without using a for loop, then write your code in VHDL or Verilog. Below is an example of this:

// Example Software Code: For (int i=0; i<10; i++) data[i] = data[i] + 1;

This code will take every value in the array “data” and increment it by 1. Here is equivalent code in VHDL:

P_INCREMENT : process (clock) begin if rising_edge(clock) then if index < 10 then data(index) <= data(index) + 1; index <= index + 1; end if; end if; end process P_INCREMENT;

And here is equivalent code in Verilog:

always @(posedge clock) begin if (index < 10) begin data[index] <= data[index] + 1; index <= index + 1; end end

Usually all you need is to add a counter signal (like index in the example above) to do the same thing that the for loop will do.

Using For Loops in Synthesizable Code

For loops can be synthesized. For loops in synthesizable code are used for expanding replicated logic. They are simply a way of shrinking the amount of code that is written by the hardware designer. They do not loop like a C program loops. They only expand replicated logic. Let’s look at an example of this. Note that the code below is written in both VHDL and Verilog, but the simulation results are the same for both languages.

VHDL Synthesizable for loop example code:

The two processes perform exactly the same functionality except the for loop is more compact. For loops can also be used to expand combinational logic outside of a process or always block. For that, you need to use a Generate Statement.

library ieee; use ieee.std_logic_1164.all; use ieee.numeric_std.all; entity Example_For_Loop is port ( i_Clock : std_logic ); end Example_For_Loop; architecture behave of Example_For_Loop is signal r_Shift_With_For : std_logic_vector(3 downto 0) := X"1"; signal r_Shift_Regular : std_logic_vector(3 downto 0) := X"1"; begin -- Creates a Left Shift using a For Loop p_Shift_With_For : process (i_Clock) begin if rising_edge(i_Clock) then for ii in 0 to 2 loop r_Shift_With_For(ii+1) <= r_Shift_With_For(ii); end loop; -- ii end if; end process; -- Performs a shift left using regular assignments p_Shift_Without_For : process (i_Clock) begin if rising_edge(i_Clock) then r_Shift_Regular(1) <= r_Shift_Regular(0); r_Shift_Regular(2) <= r_Shift_Regular(1); r_Shift_Regular(3) <= r_Shift_Regular(2); end if; end process; end behave;

Verilog Synthesizable For Loop Example Code

The two always blocks below perform the same purpose, except one uses a for loop and the other does not. Again, all the loop does is to expand replicated logic.

module for_loop_synthesis (i_Clock); input i_Clock; integer ii=0; reg [3:0] r_Shift_With_For = 4'h1; reg [3:0] r_Shift_Regular = 4'h1; // Performs a shift left using a for loop always @(posedge i_Clock) begin for(ii=0; ii<3; ii=ii+1) r_Shift_With_For[ii+1] <= r_Shift_With_For[ii]; end // Performs a shift left using regular statements always @(posedge i_Clock) begin r_Shift_Regular[1] <= r_Shift_Regular[0]; r_Shift_Regular[2] <= r_Shift_Regular[1]; r_Shift_Regular[3] <= r_Shift_Regular[2]; end endmodule module for_loop_synthesis_tb (); // Testbench reg r_Clock = 1'b0; // Instantiate the Unit Under Test (UUT) for_loop_synthesis UUT (.i_Clock(r_Clock)); always #10 r_Clock = !r_Clock; endmodule

For Loop Simulation Results

As can be seen in the example above, all the for loop does for synthesis is to expand replicated logic. It will essentially unwrap the entire loop and replace the loop with the expanded code. The signals r_Shift_With_For and r_Shift_Regular behave exactly the same way! Now let’s look how for loops can be used in simulation.

Using For Loops in Simulation

For loops when used in a simulation environment can behave more like the traditional for loop that you have seen in other software programming languages. They can have delays inside them and can actually delay the simulation while executing them.

The example below will initialize r_Data in an incrementing pattern, assigning one value every 10 ns of simulation time. It also displays the values as it assigns them. This is not synthesizable code!

VHDL Implementation

library ieee; use ieee.std_logic_1164.all; use ieee.numeric_std.all; entity for_loop_simulation is end entity for_loop_simulation; architecture behave of for_loop_simulation is type t_Data is array (0 to 5) of integer; begin process is variable r_Data : t_Data; -- Create 6 words deep array of integers begin for ii in 0 to 5 loop r_Data(ii) := ii*ii; report("r_Data at Index " & integer'image(ii) & " is " & integer'image(r_Data(ii))); wait for 10 ns; end loop; assert false report "Test Complete" severity failure; end process; end architecture behave;

Verilog Implementation

module for_loop_simulation (); integer ii=0; reg [7:0] r_Data[5:0]; // Create reg 8 bit wide by 6 words deep. initial begin for (ii=0; ii<6; ii=ii+1) begin r_Data[ii] = ii*ii; $display("Time %2d: r_Data at Index %1d is %2d", $time, ii, r_Data[ii]); #10; end end endmodule Console Result from Modelsim Simulation: (Same for both VHDL and Verilog Examples above) # Time 0: r_Data at Index 0 is 0 # Time 10: r_Data at Index 1 is 1 # Time 20: r_Data at Index 2 is 4 # Time 30: r_Data at Index 3 is 9 # Time 40: r_Data at Index 4 is 16 # Time 50: r_Data at Index 5 is 25