G4ODC5R - G4 Low-voltage Mechancial Relay Output, 5 ... - Opto22

Products > G4ODC5R

Hover over image to zoom in G4 Low-voltage Mechancial Relay Output, 5 VDC logic, normally open

Please contact your local distributor for pricing and purchase information.

Data Sheet Production Specification

• Description
• Specifications
• Documents
• Downloads
• Videos & Demos

G4 I/O family The G4ODC5R is a low-contact-resistance DC output. It is a single-pole, single-throw, normally open mechanical relay (Form A, SPST-NO). It was designed for a low-voltage DC load that is purely resistive (no inrush current). Typical applications for these modules include analog signal and communication line multiplexing. Because of their low 10 VA rating, these modules are not recommended for inductive or capacitive loads (even very small loads) because the inrush current is likely to exceed the 10 VA rating. IMPORTANT: Applications using 120 VAC are typically NOT suited to this module. If you are considering using this module for any application other than low-voltage purely resistive loads, see the detailed notes and rating curve in the data sheet, and call Pre-sales Engineering for specific guidance.

Units	G4ODC5R	G4ODC5R5
Contact form	Form A SPST mechanical relay	Form B SPST mechanical relay	NOTE: The application of the dry contact module must not exceed 10 VA under steady-state or momentary in-rush condi­tions. For voltages at or below 20 volts, the current limit is 0.5 amps. For voltages above 20 volts, the maximum allowable current is deter­mined by the following equation: Maximum Current = 10 VA / Voltage
Normal position	Open	Closed
Contact rating	VA	10		10
Maximum switching voltage (see Note)	VDC	100		100
	VAC	130		130
Maximum switching current	A	0.5 (see Note)		0.5 (see Note)
Contact resistance	Milliohms	200		200
Turn-on time	microseconds	500		500
Turn-off time	microseconds	500		500
Contact bounce	microseconds	250		250
Mechanical life	cycles	5 million		5 million
Logic voltage range	VDC	4.8–6		4.8–6
Logic OFF voltage range	VDC	0.0–0.8		0.0–0.8
Logic ON voltage range	VDC	3.8–6		3.8–6
Indeterminate range	VDC	0.8–3.8		0.8–3.8
Logic input current at nominal logic voltage	milliamps	14		14
Isolation voltage (transient) input-to-output	VDC	1,500		1,500
Ambient temperature: Operating Storage	°C °C	0 to 70 -60 to +105		0 to 70 -60 to +105
Agency Approvals	CE, CSA, UKCA	CE, CSA, UKCA

0364

G4 Digital Dry Contact Output Modules Data Sheet

Opto 22’s G4 family of modules includes two dry-contact, low-contact-resistance DC output modules, the G4ODC5R and the G4ODC5R5.

View

0727

G4 Digital I/O Data Book

The G4 Digital I/O Data Book provides complete details on every G4 digital I/O product component, including adapter cards, I/O modules, and mounting racks.

View

2375

UKCA Declaration of Conformity (EMC, LVD, RoHS)

This document is the Manufacturer's Declaration of Conformity for the products listed herein, in accordance with EMC, LVD, and RoHS rules, regulations and standards of the United Kingdom. The models cited have been tested to the essential requirements listed in the Standards section, and fully comply with the legislation as listed in UK Legislation section.

View

2285

Declaration of Conformity (EMC, LVD, RoHS)

This document is the Manufacturer's Declaration of Conformity for the products listed herein, in accordance with European, international, and/or national standards and regulations.

View

1648

Opto 22 RoHS 3 Statement of Compliance - Restriction of Hazardous Substances

This document is a statement of compliance with the EU Directive 2015/863/EU, Restriction of Hazardous Substances (RoHS 3). This document lists Opto 22 products that comply with the substance restrictions of the RoHS 3 directive.

View

1058

CSA Approval Document

This document lists all Opto 22 part numbers that have the Canadian Standards Association (CSA) approval.

View

0892

CE Declaration: EMC

This document is the Manufacturer's Declaration for the listed products as mentioned in the attachment - to which this confirmation refers - that they are in accordance with Directive 2014/30/EU.

View

0891

CE Declaration: Low Voltage

This document is the Manufacturer's Declaration for the listed products as mentioned in the attachment - to which this confirmation refers - that they are in accordance with Directive 2014/35/EU.

View No downloads are available for this product. No videos or demos are available for this product.