Golf MK5 Turbo Problems - Kev Atkinson's Blog
Có thể bạn quan tâm
I thought I’d write something for the internet to find relating to a problem I had recently with my VW Golf MK 5.
It started 6-8 weeks ago with a heavy oil leak. It started as a drip under the centre of the car engine and quickly developed into loosing a litre every 300 miles. I got it in to a garage who diagnosed the actual turbo oil seals had gone so set about sorting that myself where I could.
It was new turbo time.
OEM costing £900+ I opted for a re-manufactured turbo. I did lots, and lots of internet research and ultimately found 95% of people were happy with a re-man and had no problems. So £300 lighter and I had a re-manufactured turbo.
It also cost £8 for the gasket set and a further £28 for the turbo oil feed pipe. Not happy with costing me enough, I then preventativey forked out £10 for an oil filter, and £28 for 5L of oil.
Already skint I then paid £150 to get it fitted. A new exhaust clamp was needed at the time (whilst the guy was working on the car) so there went another £10.
So that done the new turbo worked fine for 2 days. And then it ‘stopped’ working, and by that I mean there was no boost. Cars often go into ‘limp home’ mode which means you lose all boost and the car runs in a basic configuration to ‘get you home’. After checking all of the boost hoses and vacuum hoses I decided it must be either a MAP or MAF related problem. I highly doubted a new re-man turbo would fail after 30 miles.
After getting the car checked on VCDS it threw up the following errors;
- 16622 – Manifold Pressure / Boost Sensor (G31) P0238 – 000 – Signal too High
- 18000 – Altitude Sensor / Boost Pressure Sensor – P1592 – 000 – Implausible Correlation
It threw those errors despite having a known working MAP sensor, a new MAP sensor and my old MAP sensor. The MAP sensor (manifold absolute pressure sensor) measures pressure in the manifold and reports this to the ECU.
I then measured the output of the MAP sensor in VCDS and found it was reporting all sorts of boost even without the engine running. A multimeter confirmed there was a wiring fault somewhere. Below is the video of the boost pressure being measured in VCDS.
It turns out there is a VW Technical Bulletin about this which recommends the wire terminals are changed for gold plated ones. A quicker fix is to get a new MAP sensor wiring loom (around £21+VAT). A VW specialist can fit this for 2 hours labour +VAT. All in you’re looking at £145 to get it fixed. A new loom has to be hard-wired into the ECU which requires specialist tools, so needs a VW specialist to do it.
An expensive episode. £679 lighter.
Share this:
- Click to share on Twitter (Opens in new window)
- Click to share on Facebook (Opens in new window)
- Click to email a link to a friend (Opens in new window)
- Click to share on Tumblr (Opens in new window)
Like this:
Loading...Từ khóa » Vw Golf Mk5 Map Sensor Problems
-
Golf 5 MAP Sensor - Issues - The Volkswagen Club Of South Africa
-
VW Golf 5, 1.9TDI How To Change MAP Sensor /turbo Problem
-
MAP Sensor Troubleshooting
-
Mk5 Golf - Problems With Boost Pressure Sensor - Help! - Uk
-
7 Symptoms Of A Broken MAP Sensor - LiveAbout
-
MAP Sensor Bad ? | VW Vortex - Volkswagen Forum
-
More Fault Codes After MAP Sensor Replaced | VW Vortex
-
7 Symptoms Of A Bad MAP Sensor (and Replacement Cost In 2022)
-
Golf 140 Tdi Power Loss Problems - Page 2 - VW Audi Forum
-
MAP Sensor (Mk5) - VW Golf R32 Forum
-
DIY Cleaning MAP Sensor On Your Volkswagen Eos To Fix Bad Fuel ...
-
What Is This? | UK Volkswagen Forum
-
Symptoms Of A Bad Or Failing Manifold Absolute Pressure Sensor ...
-
10 Symptoms Of A Bad MAP Sensor (& Replacement Cost)