H-King J3 Navy Cub (NE-1) 1400mm (PnP) Complete Build Guide ...

Trang chủ » H-king J3 Navy Cub (ne-1) 1400mm » H-King J3 Navy Cub (NE-1) 1400mm (PnP) Complete Build Guide ...

Có thể bạn quan tâm

Pages

  • Home
  • Coauthor
  • DIY Tricycle Landing Gear

Sunday, April 9, 2017

H-King J3 Navy Cub (NE-1) 1400mm (PnP) Complete Build Guide and Unboxing

We are going to be taking a look at the H-king J3 cub Navy edition. First things first, I would just like to say that I was impressed by the extremely fast shipping. It had been dispatched from the international warehouse and was at my house in three days. Moving on to unboxing, although the box was slightly dented, nothing inside was damaged. The quality of the foam on this model is incredible, with the molded ribbing in the wings and how smooth it is. Unlike the gloss coating that non- naval cubs carry, this model perfectly exemplifies the traditional matte blue and gray scheme carried by the 230 navy cubs used in WWII. the foam is both a blessing and a curse, however, as it creases and wrinkles more than on less scale frames. this means you need to be more careful in the assembly, transportation, and flying process if you want to maintain the beauty of this model. I found that the landing gear was especially difficult to piece together. When you attach the rear wheel, first install the servo and c-clip looking thing that looks like this. attach the Z-Bend servo rods to the Servo base and the tail wheel, THEN you can go ahead and screw the tail wheel into place. When you go to install the main gear, it might look like the pieces don't fit, don't worry, and DON'T try and force it into place. Take the wing struts and place them in these slots then screw the landing gear on top. Install the gear dam to secure the wheels. after the landing gear was assembled, the rest was relatively easy to piece together. One thing I would like to see in future models from h-king is better directions or labeling on the screws used on the model. I ended up having to glue the horizontal and vertical stabilizers on instead of screwing them because I used the wrong screws and they got stuck. If you look closely in the bag of goodies that came with this model, you can find strips of wire with loops at the end, along with a bag of tiny springs. Also, look for a bag with plastic securing hardpoints. we are going to be using the small ones, so save the others for the wings. These pieces are used for supporting the vertical stabilizer on the REAL airplane. On this model, they are more for looks, but man does they look good once you put them on. This model also comes with the hardware to put them on the bottom as well, but I left them off because I might fly through grass sometime, which would knock these off. Glue the larger hardpoints to the wing. Again, I used hot glue for this. Next, comes the wing assembly. Use the included fiber rods and slide them into their designated slots. The wider diameter, shorter length rod goes in the middle slot and the two small diameters, long length rods go on either side. you might need to slide them in and out a couple times to make it easier to put together. I used hot glue to secure both wing halves. At this point, you are going to want to bind your radio to the plane. I didn't show this part in the process because everyone uses a different radio system. Plug the "y" connector into the aileron wings and connect it to the plane. when you plug the servos in, they will automatically center, allowing you to plug in the control rods and linkages. install the servo horns with these screws. I only used two screws on each, but you can use all four if you want. make sure the servos are centered in the fuselage, then attach the linkage ends to the control horns. We're almost done! Next, plug the wing struts into the wings and use the same screws you used for the control horns to hold them in place. after you finish this step, flip the plane over and install the propeller. You're Done! Overall, this is an amazing model at a super low cost. it shipped fast and although some parts were difficult to understand, it went together quite well. I would highly recommend this model to anyone who has previous building experience or a love for scale models. Make sure to subscribe if you like the video. I will be posting a maiden flight video in the coming weeks, so make sure you don't miss it! Statik Building rating: 8.5 out of ten Posted by at 3:15 PM

No comments:

Post a Comment

Newer Post Older Post Home Subscribe to: Post Comments (Atom)

StatiK RC

Loading...

Translate

Popular Posts

  • Drone Base Honest Review Before I begin this review, I would like to say that I was not sponsored, paid, or compensated in any way for writing this review. These a...
  • H-King J3 Navy Cub (NE-1) 1400mm (PnP) Complete Build Guide and Unboxing We are going to be taking a look at the H-king J3 cub Navy edition. First things first, I would just like to say that I was imp...
  • How To: Reverse a Servo with the FRSKY Taranis  If you want to reverse a servo or control input in the Taranis, you are in luck because there are two easy ways to do this. For the fir...
  • Quanum Falcon Billet Block FPV Racing Frame REVIEW Quick Overview: The Quanum Falcon frame is a QAV 250 knock-off race quad frame from Hobbyking. As you  have probably noticed from most...
  • AMA Reacts to DOT UAS Registration Rule AMA Reacts to DOT UAS Registration Rule
  • Dragonfly-1 review The dragonfly-one is a fun Hobbyking Sunday flyer with very nice characteristics. Where it excels is at being a small, throw-in-the-back-o...
  • DYS 250 Review As you have probably noticed from my recent videos, I have been flying the DYS 250...A LOT! Here is a review of this particular quad. O...
  • PVC Air Gates for Multi-Rotor Racing Recently (as you can probably tell by some of my latest videos) I have gotten involved in multi-rotor racing. I noticed however, that air-g...
  • DLG!!! Well...Since you decided not to vote, I will go off of the design I voted for (a DLG). For those of ...
  • CC3D wont connect to openpilot GCS? Try this: This is an awesome failproof method for FORCING the computer to connect to your board. I have used this process many times when a beta-fl...

Blog Archive

  • ▼  2017 (31)
    • ▼  April (5)
      • Magnus Effect - Why does it work? EXPLANATION
      • Josh Bixler can make your wings (hands) clap - Fli...
      • End of Thursday posts
      • H-King J3 Navy Cub (NE-1) 1400mm (PnP) Complete Bu...
      • Late Video

Từ khóa » H-king J3 Navy Cub (ne-1) 1400mm