Install And Configure NTP Server And Client On Centos 7 - OrcaCore

In this article, we want to teach you to Install and Configure NTP Server and Client on Centos 7.

Network Time Protocol (NTP) is an internet protocol used to synchronize with computer clock time sources in a network. It belongs to and is one of the oldest parts of the TCP/IP suite. The term NTP applies to both the protocol and the client-server programs that run on computers.

Install and Configure NTP Server and Client on Centos 7

Before you start to set up NTP on your server, you need to log in to your server as a non-root user with sudo privileges. To do this, you can follow our article the Initial Server Setup with Centos 7.

Now follow the steps below to complete this guide.

Install NTP Server on Centos 7

First, you need to update your local package index with the following command:

sudo yum update -y

Then, you can install NTP packages on Centos 7 with the following command:

sudo yum install ntp -y

At this point, you need to configure the NTP server.

NTP Server Configuration on Centos 7

To add NTP Server information in /etc/ntp.conf, you need to open the file with your favorite text editor, here we use vi:

sudo vi /etc/ntp.conf

You need to provide the NTP Server IP or hostname with the server keyword. You can also add the Server information at the end of the file.

# For more information about this file, see the man pages # ntp.conf(5), ntp_acc(5), ntp_auth(5), ntp_clock(5), ntp_misc(5), ntp_mon(5). driftfile /var/lib/ntp/drift # Permit time synchronization with our time source, but do not # permit the source to query or modify the service on this system. restrict default nomodify notrap nopeer noquery # Permit all access over the loopback interface. This could # be tightened as well, but to do so would effect some of # the administrative functions. restrict 127.0.0.1 restrict ::1 # Hosts on local network are less restricted. #restrict 192.168.1.0 mask 255.255.255.0 nomodify notrap # Use public servers from the pool.ntp.org project. # Please consider joining the pool (http://www.pool.ntp.org/join.html). server 0.centos.pool.ntp.org iburst server 1.centos.pool.ntp.org iburst server 2.centos.pool.ntp.org iburst server 3.centos.pool.ntp.org iburst

When you are done, save and close the file.

Restrict NTP Server Access

If you want to restrict the NTP Server access for some of the clients, you can edit the /etc/ntp.conf file and replace the network information with the client network and their subnet mask information. This will restrict the given Client’s access.

restrict 192.168.1.0 mask 255.255.255.0 nomodify notrap

Now restart your NTP service on Centos 7 with the command below:

sudo systemctl restart ntpd

Enable your NTP server to start on boot on Centos 7:

sudo systemctl enable ntpd

Next, you can check your NTP Synchronization Status with the following command:

ntpq -np Output remote refid st t when poll reach delay offset jitter ============================================================================== *91.216.151.61 131.130.251.107 2 u 3 64 1 4.126 -1.069 2.578 162.159.200.1 10.50.9.36 3 u 2 64 1 0.327 -0.593 0.092 2a00:ff0::19 36.224.68.195 2 u 1 64 1 49.357 -0.264 1.640 86.127.71.168 115.75.236.158 2 u 2 64 1 5.637 -1.318 0.178

If everything went well then Your date and time should be synchronized from the NTP Server on Centos 7. You can verify your timezone with the following command:

timedatectl Output Local time: Sat 2022-04-16 03:36:54 EDT Universal time: Sat 2022-04-16 07:36:54 UTC RTC time: Sat 2022-04-16 07:36:53 Time zone: America/New_York (EDT, -0400) NTP enabled: yes NTP synchronized: yes RTC in local TZ: no DST active: yes Last DST change: DST began at Sun 2022-03-13 01:59:59 EST Sun 2022-03-13 03:00:00 EDT Next DST change: DST ends (the clock jumps one hour backwards) at Sun 2022-11-06 01:59:59 EDT Sun 2022-11-06 01:00:00 EST

If you want to query from NTP Server and check the current offset and delay, you can use the command below. For example:

ntpdate -q pool.ntp.org Output server 162.159.200.123, stratum 3, offset -0.001746, delay 0.02603 server 86.127.71.168, stratum 2, offset -0.002588, delay 0.03148 server 93.190.144.28, stratum 2, offset -0.001501, delay 0.02661 server 162.159.200.1, stratum 3, offset -0.001788, delay 0.02602 16 Apr 03:37:34 ntpdate[30123]: adjust time server 93.190.144.28 offset -0.001501 sec

Install NTP Client on Centos 7

At this point, you can install the NTP on your Client’s machine. Here our client machine is Centos.

Install your NTP client with the command below:

sudo yum install ntp

NTP Client Configuration on Centos

Then, configure your ntp.conf file and point to your NTP server:

sudo vi /etc/ntp.conf server your-server-ip-address

When you are done, save and close the file.

Next, restart your NTP client:

sudo service ntpd restart

Test your NTP client status whether properly configured or not by running the below command:

ntpq -p

Conclusion

At this point, you learn to Install and Configure NTP Server and Client on Centos 7.

Hope you enjoy it.

You may be like these articles:

Install and Configure NTP Server and Client on AlmaLinux 9

Set up and Configure NTP Server and Client on Rocky Linux 8

Install and Configure NTP Server and Client on Ubuntu 22.04