Material Data Center | Datasheet Badaform® C110 TM-Z1

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Badaform® C110 TM-Z1 - POM - Bada AG

Material Data Center offers the following functions for Badaform® C110 TM-Z1:unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Badaform datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet: Processing/Physical Characteristics - Mechanical properties - Thermal properties - Electrical properties - Other properties - Processing Recommendation Injection Molding Any use of this information falls under the rules of our disclaimer.

Processing/Physical Characteristics	Value	Unit	Test Standard
ISO Data
Melt volume-flow rate, MVR	8	cm³/10min	ISO 1133
Temperature	190	°C	-
Load	2.16	kg	-

Mechanical properties	Value	Unit	Test Standard
ISO Data
Tensile Modulus	1900	MPa	ISO 527
Yield stress	50	MPa	ISO 527
Yield strain	12	%	ISO 527
Flexural strength	45	MPa	ISO 178
Charpy impact strength, +23°C	N	kJ/m²	ISO 179/1eU
Charpy notched impact strength, +23°C	12	kJ/m²	ISO 179/1eA
Izod notched impact strength, +23°C	12	kJ/m²	ISO 180/1A
Ball indentation hardness	100	MPa	ISO 2039-1

Thermal properties	Value	Unit	Test Standard
ISO Data
Melting temperature, 10°C/min	167	°C	ISO 11357-1/-3
Temp. of deflection under load, 1.80 MPa	95	°C	ISO 75-1/-2
Vicat softening temperature, B	130	°C	ISO 306
Coeff. of linear therm. expansion, parallel	130	E-6/K	ISO 11359-1/-2
Burning behav. at 1.5 mm nom. thickn.	HB	class	IEC 60695-11-10
Thickness tested	1.6	mm	-

Electrical properties	Value	Unit	Test Standard
ISO Data
Relative permittivity, 1MHz	4	-	IEC 62631-2-1
Dissipation factor, 1MHz	100	E-4	IEC 62631-2-1
Volume resistivity	1E11	Ohm*m	IEC 62631-3-1
Surface resistivity	1E13	Ohm	IEC 62631-3-2
Electric strength	20	kV/mm	IEC 60243-1
Comparative tracking index	600	-	IEC 60112

Other properties	Value	Unit	Test Standard
Humidity absorption	0.3	%	Sim. to ISO 62
Density	1380	kg/m³	ISO 1183

Processing Recommendation Injection Molding	Value	Unit	Test Standard
Pre-drying - Temperature	100	°C	-
Pre-drying - Time	1 - 3	h	-
Processing humidity	≤0.2	%	-
Melt temperature	180 - 210	°C	-
Mold temperature	60 - 90	°C	-

CharacteristicsProcessingInjection MoldingSpecial CharacteristicsHigh impact or impact modifiedFeaturesCopolymerRegional AvailabilityNorth America, Europe, Asia Pacific, South and Central America, Near East/AfricaDisclaimerCopyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.