N/m2 – Newton Per Square Metre Pressure Unit - SensorsONE

Newtons/Square Meter is a unit that shows how the pascal unit is derived from other SI units. Pressure is defined as Force/Area and the SI unit for Force is newtons (N) and the SI unit for Area is Sq Meters (m²). 1 newton per square metre equals 1 pascal.

The N/m² pressure unit is one of the few units that clearly describes what pressure represents in its name symbol. Although it is not generally used to describe a pressure reading, it can be useful for calculating the force required to generate a certain pressure.

For example if you know the cross sectional area of the inside of a hydraulic ram cylinder (sqm), you can then calculate the required force (N) to generate a particular pressure in pascals (Pa) by multiplying the two together.

Alternatively you can calculate the hydraulic ram area size (m²) needed by dividing the available Force (N) by the Pressure (Pa) or determine the pressure (N/m²) produced by the hydraulic system by dividing the Force (N) by the Hydraulic ram area (m²).

You can convert a reading in newtons per sq metres into another pressure unit by multiplying it by the relevant converting value listed below.

If you would like to use a tool to convert several values please use our pressure unit converter to save time.

Featured n/m2 - newtons per square metre based unit range pressure measurement products

• Pitot tube air flow calculation 1000 hPa differential pressure transmitter - Air flow differential pressure transmitter for measuring difference between pitot tube and static port pressure up to 1000 hectopascals.
• Heating appliance chimney draft and barometric pressure testing using differential and absolute sensors - Very low, bi-directional chimney draft pressure and barometric pressure sensor for testing preformance of wood stoves in a research environment.

Conversion Factors

• 0.00001 bar
• 0.0001450377 psi
• 0.01 mbar
• 1 N/m²
• 1 Pa
• 0.01 hPa
• 0.001 kPa
• 0.000001 MPa
• 0.0000101972 kg/cm²
• 0.101972 mmH2O 4°C (39.2°F)
• 0.0101972 cmH2O 4°C (39.2°F)
• 0.000101972 mH2O 4°C (39.2°F)
• 0.00401463 inH2O 4°C (39.2°F)
• 0.000334553 ftH2O 4°C (39.2°F)
• 0.00750062 mmHg 0°C (32°F)
• 0.000750062 cmHg 0°C (32°F)
• 0.000295300 inHg 0°C (32°F)
• 0.00750062 Torr
• 7.50062 mTorr
• 0.00000986923 atm
• 0.0000101972 at
• 10 dyn/cm²
• 0.00232060 oz/in²
• 7.50062 µHg 0°C (32°F)
• 0.0000000647490 tsi (uk, long)
• 0.0000000725189 tsi (usa, short)
• 0.0000104427 tsf (usa, short)
• 0.0208854 psf
• 0.0101972 g/cm²

Please note that the conversion factors above are accurate to 6 significant figures.

Conversion Tables

Select a look up table for converting a pressure reading in newtons per square metre to other measurement units.

• bar  »  100 to 200,000 N/m² → 0.001 to 2.000 bar
• psi  »  100 to 200,000 N/m² → 0.0145038 to 29.0075 psi

Featured n/m2 - newtons per square metre based unit range pressure measurement products

• -10…30 kPa g compound range inert gas pressure transmitter for ship IG system - An intrinsically safe, marine approved compound range pressure transmitter for ship cargo tank IG system use to measure pressure of inert gas over a range of -10 to 30 kPa g from the G1/2 male process connection, and sending the corresponding 4-20mA signal through the DIN plug electrical connection.
• 10 kPa orifice plate differential pressure transmitter for water flow measurement - Pressure sensor for measuring the differential pressure generated by water flowing through an orifice plate in a pipe, and converting the output to a water flow measurement.