Neumann KH 870 G Aktiv Sub - ProLyd

Có thể bạn quan tâm

Improving lateral consistency

The latest amplifier technology and acoustical components have been used to ensure the most accurate sound reproduction possible. Robust drivers, a rock-solid cabinet, and carefully designed ports guarantee a tight, articulate, and distortion-free low frequency reproduction, even at high replay levels. Using the sum output, Plane Wave Bass Array™ (PWBA™) techniques acoustically improves lateral consistency in the listening area. The bass extends down to 18 Hz.

Flexible mounting options

The KH 870 subwoofer is designed to complement Neumann's extensive range of monitors, and can be used on its own, or daisy-chained to make larger systems capable of higher SPL. The KH 810 can be used in music, broadcast, and post production studios for tracking, mixing, and mastering. The cabinet can be positioned next to a wall or flush mounted into a wall due to the front mounted port, and can be mixed freely in multichannel systems with other loudspeakers from Neumann's range.

Applications

Bass extension for loudspeakers down to 18 Hz
Increasing the maximum SPL of loudspeakers by up to 8 dB
Decreasing harmonic and intermodulation distortion of loudspeakers
Reproducing the LFE channel
Reproducing the “Sub” signal of a bass managed multichannel source
Making a Plane Wave Bass Array™ system
Working as an extension for KH line subwoofer systems

Computer mechanically modeled cabinet design using Low resonance Integral Molding™ (LRIM™) materials

Wooden cabinet with a tough painted finish and high density rubber isolating feet
Excellent self-damping properties leading to minimal cabinet resonances
No standing wave resonances inside cabinet
Reduced cabinet resonances

(2) In-house modelled long-throw composite sandwich cone bass driver with Extremely Linear Force Factor™ (ELFF™), magnetic shielding, flow optimized die cast basket and robust built-in grille

Damping of break up modes brings low distortion at high sound levels
Linear pistonic motor gives a very low harmonic distortion even at high excursions
Reduced air noise and improved rocking modes
Grille protects against mechanical damage

(3) Large high-capacity flow-optimized bass reflex ports

Fast bass transient response
Reduced bass compression at high output levels
Can be flush mounted

(4) XLR electronically balanced analogue inputs and outputs

Standard interfacing to professional equipment
Daisy chain output for subwoofer arrays

7.1 High Definition Bass Management

Compatible with all systems from mono to 3D
Bypassable 4th order 80 Hz active crossover for maximum compatibility with consumer reproduction systems
Allows main loudspeakers to play louder and with lower distortion

(5) Remote control

NRC 1 and SEA 1 hardware remote control
RS-232 control possible

(6) LFE gain

0 and +10 dB

Four routing modes

LFE to subwoofer and left/right
LFE to subwoofer only up to 80 Hz
LFE to subwoofer only up to 120 Hz
LFE to subwoofer with no filtering – for daisy chaining subwoofers and external signal processing systems

(7) Wide range input gain and output level controls

Easier interfacing with signal sources

8-position phase control (with built in test tone), continuous low cut control and parametric equalizer

More control in diverse acoustical environments
Parametric equalizer is bypassable if not needed

(8) Bass Management controls

Bypassable
Independent control of bass management bypass for front and back channels
System volume control on/off

(9) Universal switched-mode power supply (100 … 240 V)

One version works in any country and robust to poor quality mains supply
Electronics can be remotely powered on with two modes of operation (0 V and 12 V trigger)

(10) Ground lift

Reduced noise in electrically noisy environments and over-comes ground loops

(11) Sum output

Larger systems and Plane Wave Bass Arrays™ maybe constructed using the Sum output

(12) Low heat dissipation amplifiers with large headroom and overheat limiting

Improved transient response
Assured reliability and safety

Separate fast acting thermo limiter to protect the voice coil and power amplifier

Soft clip and excursion limiters
Increases system reliability
Allows extraction of the maximum performance from the system

(13) Installation flexibility

Remoteable electronics (REK 3) for ease of installation, less cabling, and convenience of use

Free field frequency response ±6 dB	17 … 600 Hz
Free field frequency response ±3 dB	18 … 300 Hz
Reproduction accuracy between 50 Hz and 100 Hz: 100%, 80%, 50% of subwoofers produced	±1.20; ±0.54; ±0.28 dB
Self-generated noise at 10 cm (with input gain set to 100 dB SPL for 0 dBu)	<20 dB(A) SPL
Sine wave output with a THD < 0.5 % at 1 m in half space	95 dB SPL (>40 Hz)
Bass capability: Max. SPL in half space at 3% THD at 1m (averaged between 50 Hz and 100 Hz)	116.7 dB SPL
Max. long term SPL with pink noise at 2.3 m, in typical listening conditions (single / pair full range)	118 dB SPL
Analog input(s)	8 x XLR: analog electronically balanced
Analog input impedance	>13k Ohms
Max. input level	+19 dBu
Common mode rejection ratio (CMRR)	> 56 dB @ 15 kHz
Crosstalk (1 kHz), level matching	-95 dB; ±0.1 dB
Volume control	NRC 1 hardware remote or RS-232
Volume control range; resolution	118 dB; 0.25 dB
Analog dynamic range; THD+N	119 dB(A); <0.001% (-100 dB)
Signal routing modes	LFE 80+re-routing; LFE 80 Hz; LFE 120 Hz; Wide
LFE Gain	0 / +10 dB
Analog output(s)	8 x XLR; analog electronically balanced
Input gain control (sensitivity)	+2 ... -12 dB
Output level control (output level in 1 m based on 0 dBu input level)	100; 114 dB SPL
Controller design	Analog, active
Crossover frequency	80 Hz
Crossover slope	24 dB/oct; 4th order
Equalization: Low cut	30 Hz; 0 … -12 dB
Equalization: Parametric EQ: Gain	+4 ... -12 dB
Equalization: Parametric EQ: Frequency	Bypass; 20 ... 120 Hz
Equalization: Parametric EQ: Q	1 ... 8
Phase	0; 45; 90; 135 and 0/180 deg
Protection circuitry	Peak and thermo limiters
Infrasonic filter: frequency; slope	6.5 Hz; 12 dB/oct.
Remote control	RJ45 connector: Via NRC1 remote control (optional): volume for all channels; bass management on/off; LFE gain 0/10 dB.Via RS-232: more parameters remote controllable
Display: On; Normal Operation	Red LED
Display: Limit / Clip / Errors / Protection /Boot Mute / Shut Down Mute	Red LED
Display: Bass Management on	Green LED
Output power woofer amplifier (THD+N with limiter deactivated: 10%)	400 W
Output power woofer amplifier (THD+N with limiter deactivated: 0.1%)	320 W
Mains Power Supply: input voltage; frequency	220-240 / 100-120 V (switchable); 50/60 Hz
Power consumption (230 V / 100 V): Idle	25 W
Power consumption (230 V / 100 V): Full output	550 W
Cabinet material	Wood cabinet, aluminum electronics panel
Cabinet surface finish; color (front / back)	Painted; metallic anthracite (RAL 7021) / black (RAL 9005)
Operating conditions	+10° C to +40° C (+50° F to +104° F); <90% RH, non-condensing
Transport/storage conditions	-25° C to +70° C (-13° F to 158° F); <90% RH; non-condensing
Woofer	2 x 265 mm (10") with magnetic shielding and protecting black metal grille
Mounting points	35 mm flange on top panel
Product dimensions (height x width x depth)	735 x 330 x 645 mm (28.9" x 13" x 25.4")
External net volume	156 liters
Product weight	47.1 kg (103 lbs 13 oz)
Cabinet weight when electronics remote located	45.5 kg (100 lbs 5 oz)
Packed dimensions (height x width x depth), mm (inches)	860 x 470 x 770 mm (33 7/8" x 18 1/2" x 30 3/8")
Packed weight	54.3 kg (119 lbs 11 oz)
Packed cube	0.311 m³