SERVICE INFORMATION FOR DTCS C1A12 AND C1A16 - Nissan
SERVICE BULLETIN
| Classification: | Reference: | Date: |
|---|---|---|
| EL15-032b | NTB15-099b | September 6, 2016 |
SERVICE INFORMATION FOR DTCS C1A12 AND C1A16
| This bulletin has been amended. The APPLIED VEHICLES section has been revised, a photo has been added to page 4, and ICC/distance sensor location information for Maxima and Rogue has been adjusted. No other changes have been made. Please discard previous versions of this bulletin. |
| APPLIED VEHICLES: | 2016 Altima (L33) |
|---|---|
| 2016 Maxima (A36) | |
| 2015-2016 Murano (Z52) | |
| 2016 Murano Hybrid (Z52) | |
| 2015-2016 Rogue (T32) | |
| 2016 Sentra (B17) |
SERVICE INFORMATION
As part of the diagnosis for DTC C1A16 (RADAR BLOCKED) that is stored in an APPLIED VEHICLE, be sure to check the following:
- Check the ICC/distance sensor lens or the bumper fascia in front of the sensor (see pages 2, 3, and 4). Remove any obstructions, including any clear bra or film, and clean off any stains (mud, dirt, road debris, dirty rain water, etc.), and then verify proper system operation.
As part of the diagnosis for DTC C1A12 (LASER BEAM OFFCNTR) that is stored in an APPLIED VEHICLE, be sure to check the following:
- Inspect the bumper fascia in the area in front of the ICC/distance sensor (see pages 2, 3, and 4).
- Check for stains and/or physical damage (for example, mud/dirt, road debris, dirty rain water, scrapes, punctures, misshapen surface).
- If there is physical damage but not severe, clean the area in front of the ICC/distance sensor, perform an ICC/distance sensor alignment using CONSULT-III plus (C-III plus), and then verify proper system operation.
- If an ICC/distance sensor alignment is not successful, inspect the ICC/distance sensor bracket for damage (see page 5).
- If damaged, replace the ICC/distance sensor bracket, and then perform an ICC/distance sensor alignment again.
If the above information does not resolve the issue for either DTC, refer to the Electronic Service Manual (ESM), section CCS-Cruise Control System or DAS-Driver Assistance System (as it applies), for diagnosis of the stored DTC(s).
NOTE: The Nissan
New Vehicle Limited Warranty does not cover incidents due to lack of vehicle maintenance and/or physical damage. Refer to the Nissan
Assurance Products Resource Manual (APRM) for guidelines on warranty coverage. The vehicle owner’s manual contains the complete details regarding the limited warranty.




NTB15-099b
Reload document |
Open in new tab
Download [1.51 MB]
SaleBestseller No. 1
ANCEL AD310 Classic Enhanced Universal OBD II Scanner Car Engine Fault Code Reader CAN Diagnostic Scan Tool, Read and Clear Error Codes for 1996 or Newer OBD2 Protocol Vehicle (Black) - CEL Doctor: The ANCEL AD310 is one of the best-selling OBD II scanners on the market and is recommended by Scotty Kilmer, a YouTuber and auto mechanic. It can easily determine the cause of the check engine light coming on. After repairing the vehicle's problems, it can quickly read and clear diagnostic trouble codes of emission system, read live data & hard memory data, view freeze frame, I/M monitor readiness and collect vehicle information.
- Sturdy and Compact: Equipped with a 2.5 foot cable made of very thick, flexible insulation. It is important to have a sturdy scanner as it can easily fall to the ground when working in a car. The AD310 OBD2 scanner is a well-constructed mechanic tool with a sleek design. It weighs 12 ounces and measures 8.9 x 6.9 x 1.4 inches. Thanks to its compact design and light weight, transporting the device is not a problem. The buttons are clearly labelled and the screen is large and displays results clearly.
- Accurate Fast and Easy to Use: The AD310 scanner can help you or your mechanic understand if your car is in good condition, provides exceptionally accurate and fast results, reads and clears engine trouble emission codes in seconds after you fixed the problem. This device will let you know immediately and fix the problem right away without any car knowledge. No need for batteries or a charger, get power directly from the OBDII Data Link Connector in your vehicle.
- OBDII Protocols and Car Compatibility: Many cheap scan tools do not really support all OBD2 protocols. AD310 scanner as it can support all OBDII protocols such as KWP2000, J1850 VPW, ISO9141, J1850 PWM and CAN. This device also has extensive vehicle compatibility with 1996 US-based, 2000 EU-based and Asian cars, light trucks, SUVs, as well as newer OBD2 and CAN vehicles both domestic and foreign. Pls confirm with our customer service whether it is compatible with your vehicle before purchasing.
- Home Necessity and Worthy to Own: This is an excellent code reader to travel or home with as it weighs less and it is compact in design. You can easily slide it in your backpack as you head to the garage, or put it on the dashboard, this will be a great fit for you. The AD310 is not only portable, but also accurate and fast in performance. Moreover, it covers various car brands and is suitable for people who just need a code reader to check their car.
Autel MaxiSys Elite II Pro Diagnostic Scanner - J2534 Reprogramming Tool as Ultra MS908S PRO II, OE-Level ECU Programming Tool with 150+ Car Brands Coverage, 40+ Services, 2-Year Free Updates - [2025 Autel MaxiSys Elite II Pro: Ultimate Diagnostic Powerhouse] The upgraded Elite II Pro builds on the original Elite II with a 9.7" touchscreen, octa-core processor, 128GB storage, and Android 10. Paired with Bluetooth MaxiFlash VCI/J2534 pass-thru device, it's 5X faster for diagnostics, ECU programming, and all workshop tasks - outperforming tools like Ultra and Snap-on.
- [150+ Brands & Full System Coverage] Covers 80+ US/domestic/Asian/European makes plus 70+ more with FD & DoIP protocols. Scans all vehicle systems (OBDII, ADAS, new energy vehicles) and uses 4 quick VIN methods (AutoVIN, License Plate) to pinpoint faults fast.
- [OE-Level Programming & Coding] SAE J2534 compliant for ECU reprogramming, coding, and hidden feature activation (BMW, VW, Porsche, etc.). Reprogram ECUs, match components post-repair, and flash software - works online/offline for custom builds.
- [40+ Services & Active Tests & VAG Guided] Handles Oil Reset, EPB, SAS, BMS, Injector Coding, and more. Active tests speed up issue checks; VAG Guided functions provide step-by-step OE instructions - perfect for pros. NOTE: Please check compatibility with us before purchase.
- [Built-in OEM Repair Data & Efficiency] Access wiring diagrams, TSBs, DTC solutions, and ADAS details directly on the tablet – no shared workstations needed. One-stop multitasking organizes data files, customer info, and vehicle records for streamlined workshop operations.
FOXWELL NT301 OBD2 Scanner Live Data Professional Mechanic OBDII Diagnostic Code Reader Tool for Check Engine Light - [Vehicle CEL Doctor] The NT301 obd2 scanner enables you to read DTCs, access to e-missions readiness status, turn off CEL(check engine light) or MIL, reset monitor, read live data and retrieve VIN of your vehicle. The fault code only can be cleared by NT301 after car repair finished, as like all the obd2 scanner's working principle. The fault code will appear again even though you cleared before, if you don't repair the car well.
- [Accuracy & Streams] Live data graphing and logging. Accurately read error codes for most Worldwide cars, SUVs, light trucks and 12V diesels equipped with Obd2. Graphing live vehicle sensors data allows you to focus on any suspicious data and trend. It's a basic code reader and doesn't support to scan and read codes about any car systems like ABS, Battery, TPMS, SRS, SAS systems. It also DOESN'T support any special functions like EPB reset/battery registration/oil reset/programming/Relearn/Camshaft position or battery test.
- [Read Fault Codes] About the read code funtion needs to be in the ignition on state and if the check engine light is on. If the vehicle is compatible with NT301, please select correct menu & ensure no hardware/wiring issues/obd2 interface damage for accurate results. The correct menu: Select OBDII-> Wait for seconds-> Select Read codes
- [S-mog Check Helper] Read/Erase and I/M readiness hotkeys make it easy to use the car computer reader right out of the package. Red-Yellow-Green Leds and build-in speaker indicate the readiness status for confident e-missions test.
- [OBDII Protocols & Compatibility] The NT301 supports OBDII protocols like KWP2000, J1850 VPW, ISO9141, J1850 PWM and CAN. The device is compatible with 1996 US-based, 2000 EU-based and Asian cars, light trucks, SUVs. Kindly check the vehicle compatibility before the purchase since the function comatibility and car compatibility vary from different car models, year and vin.
TOPDON RLink J2534 Pass-Thru Programmer, OEM Reprogramming and Diagnostic Tool, Enhanced J2534 VCI, Supports J2534/D-PDU/CAN-FD/DoIP, Compatible with 17+ Vehicle Brands, No OE Software Provided - J2534 Pass-Thru Programmer: TOPDON RLink J2534 is an advanced diagnostic and reprogramming tool that support all J2534 protocols, as well as D-PDU, CAN-FD and DoIP, ensuring compatibility with a wide range of modern vehicles. It offers extensive versatility with support for over 13 major automotive brands, including Chrysler, Ford, GM, Nissan
, Toyota, Honda, Subaru, Land Rover/Jaguar, Volvo, Wuling, Volkswagen/Audi, Mercedes-Benz, and BMW, enjoy dealership-level functions at your fingertips - All-in-One OEM Diagnostics: This J2534 ECU programming tool elevates your automotive repair capabilities to new heights by delivering complete OEM diagnosis. Boasting comprehensive full-system diagnostics, intuitive repair guides, advanced ECU programming and coding, common reset services, a vast library of repair information and more, this all-in-one solution empowers technicians to effortlessly tackle complex vehicle issues with ease. *Not compatible with 24V vehicles
- Proven Performance You Can Trust: Backed by over 10000 real vehicle tests and benefit from a wealth of practical experience, this OEM reprogramming tool guarantees stable and exceptional performance. Supported by TOPDON's dedicated technical experts with in-depth knowledge of both auto repair and J2534 Pass-Thru programming, the RLink J2534 provides prompt and professional assistance, ensuring a smooth setup and reliable compatibility
- Integrated Excellence, Always Up-to-Date: Featuring the exclusive RLink Platform to provide a streamlined experience with one-click driver installation and management, ensuring flawless integration with your OE software, maintaining the original performance quality. The built-in operation guide makes mastering OE software quick and easy, so you can get started right away. Plus, with lifetime free updates, your diagnostics will stay current with the latest drivers and innovations
- Efficiency Meets Versatility: Engineered to support three CAN channels simultaneously - CAN FD and CAN-CC included, giving you the edge in fast troubleshooting. To perfectly synchronized with the OE software, please diagnose with active subscriptions and make sure your computer system is running a compatible 64-bit Windows version (7, 8, 10 or later) to fully leverage the power of RLink J2534. *We don't provide extra OE software
FOXWELL Car Scanner NT604 Elite OBD2 Scanner ABS SRS Transmission, Check Engine Code Reader for Cars and Trucks, Diagnostic Scan Tool with SRS Airbag, Automotive Diagnostic Tool with Live Data - [Easy to Use—Work Out of the Box] + [FOXWELL 2025 New Version] FOXWELL NT604 Elite scan tool is the 2025 new version from FOXWELL, designed for car owners who want to figure out the cause of issues before fixing car problems by scanning common systems like ABS, SRS, engine, and transmission. The NT604 Elite obd2 scanner diagnostic tool comes with the latest software, ready to use out of the box—no need to waste time downloading software first.
- [Affordable] + [Reliable Car Health Monitor] Will you be confused what happens when the warning light of ABS/SRS/transmission/check engine flashes? Instead of taking your cars to dealership, this FOXWELL scanner will help you do a thorough scanning and detection for your cars and pinpoint the root cause. It will t-urn off the car warning light after the problem is fixed.👉TIPS: Airbag crash/collision data can NOT be cleared even if you replace the new airbag.
- [5 in 1 Car Diagnostic Scanner] Compared with obd scanners (50-100), NT604 Elite code scanner not only includes their OBDII diagnosis but also serves as ABS/SRS scanner, transmission and check engine code reader. When it’s an odb2 scanner, you can use it to check if your car is ready for annual test through I/M readiness menu. In addition, live data stream, built-in DTC library, data play back and print, all these features are a big plus for it. Note: doesn't support maintenance functions.
- [Fantastic AUTOVIN] + [No extra software fee] Through the AUTOVIN menu, this NT604 Elite car scanner allows you to get your V-IN and vehicle info rapidly, no need to take time to find your V-IN and input one by one. What's more, the NT604 Elite ABS SRS scanner supports 60+ car makes from worldwide (America/Asia/Europe). You don’t need to pay extra software fee.
- [Solid protective case KO plastic carrying bag] + [Lifetime update] Almost all same price-level car scanner diagnostic tool only offers plastic bag to hold the scanner.However, NT604 Elite automotive scanner is equipped with solid protective case, preventing your obd2 scanner from damage. Then you don’t need to pay extra money to buy a solid toolbox.
Last update on 2025-12-18 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
1SHARETừ khóa » C1b55-97
-
[PDF] 2014-infiniti-qx80-qx-69994.pdf - Snap-on Equipment
-
[PDF] Nissan; Service Information For DTCs C1A12 And C1A16 - NHTSA
-
General Vehicle Speed Control Problems Of The 2018 Nissan Altima
-
C1A16 - OBD-II DTC - port
-
Nissan OBD-II Trouble Codes
-
[PDF] DRIVER ASSISTANCE SYSTEM - NICOclub
-
[PDF] DRIVER ASSISTANCE SYSTEM - NICOclub
-
2018 Nissan Altima Service Brakes Problems - Car Complaints
-
Driver Assistance System - Z - Manualzz
-
2018 Nissan Altima Brake Consumer Complaints
-
2017 NISSAN Murano - The Center For Auto Safety
-
2018 Nissan ALTIMA Unknown Or Other Problems, Complaints And ...