SteelHead GX10000 Appliance Specifications - Riverbed Support

Trang chủ » Gx10000 » SteelHead GX10000 Appliance Specifications - Riverbed Support

Có thể bạn quan tâm

SteelHead GX10000 Appliance SpecificationsThis appendix describes the ports, LEDs, and the technical and environmental specifications for the SteelHead GX10000 appliances. SteelHead GX10000 specificationsThis section describes the ports, LEDs, and technical and environmental specifications.Port location and LEDsThese figures illustrate the port location and LEDs. Figure: SteelHead GX10000 front panelThis table summarizes the front panel LEDs and buttons.
LabelControl panel descriptionsDescription
1USB port
2NMI ButtonPuts the appliance in a halt state and issues a non-maskable interrupt (NMI). This helps when performing diagnostics for a given issue where a memory download is necessary to determine the cause of the problem. To prevent an inadvertent system halt, the NMI button is located behind the front Control Panel faceplate and is only accessible with the use of a small tipped tool such as a pin or paper clip.
3Primary Network Interface Card (NIC) activity LEDSolid Green = Network link is detected.Blinking Green = Activity. The blink rate is consistent with the amount of network activity.
4System Cold Reset ButtonReboots the appliance.
5Hardware Status LEDOff = System is powered off.Solid green = Hardware is working correctly.Blinking green= System hardware is degraded.The system is operating in a degraded state although still functional, or system is operating in a redundant state but with an impending failure warning.Note: The Hardware Status LED does not detect software issues, such as licensing status or the system becoming unresponsive. Only hardware status is shown. Blinking amber = The system is operating in a degraded state with an impending failure warning. Solid amber = The system has failed or shutdown.
Note:
6Power Button with Integrated LEDGreen = System onNo Light = System off
7Drive ActivityBlinking Green = Activity
8Auxiliary NIC activity LEDSolid Green = Network link is detected.Blinking Green = Activity. The blink rate is consistent with the amount of network activity.
9System ID Button with Integrated LEDToggles the integrated ID LED and the blue server board ID LED on and off. The System ID LED identifies the system for maintenance when installed in a rack of similar server systems. You can also remotely turn on and turn off the System ID LED using the IPMI “Chassis Identify” command which causes the LED to blink for 15 seconds.
LEDs on Disk DrivesActivity LEDBlinking Green = Read/Write Activity Disk Fault LEDOrange = Failed Disk Blinking Orange = RAID Rebuild
Figure: Back panel4The numbers 1-6 on the back panel in Figure: Back panel4 refer to card slot numbers. Numbers 24 and 25 refer to HDD/SDD slots. Slot 24 is populated with an HDD.
SpecificationDescription
Primary and AUX PortsLeft LEDSolid green = Network link is detected.Blinking Green = Activity. Right LEDNo Light (with link on left LED) = 10 MB/sec data rateGreen = 100 MB/sec data rateYellow = 1000 MB/sec data rate
LEDs on Power SupplySolid green = Power On and Healthy No AC power = OffBlinking Green = Standby or power supply firmware updatingAmber = Power Lost But Second Power Supply Has Power Blinking Amber = Power On With Warning Events (high temperature, high power, high current, slow fan)
Technical SpecificationsThis table summarizes the technical specifications for the systems.
SpecificationDescription
Form factor2U
Hard disk/SSD10 Hot Swappable Drives
Data store9.6 TB
Packaged dimensions (LxWxH)37 x 24 x 11 inch939.8 x 609.6 x 279.4 mm
Weight (without packaging)46 lbs, 20.87 Kg
Voltage frequency100-127V, 200-240V
PSU2 x 1100 W100-127Vac/10A, 50/60Hz200-240Vac/6A, 50/60Hz
PCI slots6
Maximum number of ports8
Power requirements and consumptionThis table summarizes the power specifications for the system. The system is rated at the following power characteristics when operating at nominal AC input voltages (120 V and 230 V).
SpecificationDescription
PSU type2 x 1100W
AC input230V
Max. amps.2.7
Max. watts546
Typical watts437
Max VA575
Power factor99.16
BTU (typical)1490
Environmental specificationsThis table summarizes the environmental requirements for the systems.
SpecificationDescription
Operating acoustic70 Decibels
Temperature (Operating)10º to 35ºC (50ºF to 95ºF)
Temperature (Storage)-40º to 70º C (-40º - 158º F)
Relative humidity (operating)20% to 80%, non-condensing with a maximum wet bulb of 28º C (at temperatures from 25º to 35º C)
Relative humidity (storage)50% to 90%, non-condensing with a maximum wet bulb of 28º C (at temperatures from 25º to 35º C)

Từ khóa » Gx10000