VRaySampleRate - V-Ray For 3ds Max - Chaos Help

This page gives information about the Sample Rate Render Element.

Overview

The Sample Rate Render Element displays the work being done by the image sampler as a red, green, and blue image. This render element displays the work being done on the image as it is rendering, and shows the job done when the render completes.

A color is assigned to each pixel according to how many primary samples are being taken by the Image Sampler:

• The Blue channel contains the areas which reached the desired image quality with few primary samples.
• The Green channel shows areas which required more antialiasing (AA) samples to clean up than the Blue areas, but managed to achieve the Noise Threshold within the number of AA rays used.
• The Red channel contains the parts of the image which didn't make it to the desired quality threshold, as they reached the maximum amount of AA rays before reaching the Noise Threshold.
• If the Image Sampler type is Progressive, the White areas represent the areas the sampler is currently working on, as they were found to not satisfy the Noise Threshold as of yet.

The way to ensure a render is correctly computed is to minimize the amount of red color in this render element. Raising secondary sampling through any means reduces the primary sampling work in the corresponding areas, effectively moving red areas into green ones, and green ones into blue ones. Lowering secondary samples per pixel does the opposite, potentially leading to more red areas. The suggested way to minimize the red color and optimize render times is to increase the Max AA Subdivs value (if the previous render was still noisy), or increase the Noise Threshold value (if the previous render was clean, but took too long to complete).

Note that some specific image features, like high-frequency detail often found in fur and hair, or high-contrast zones, will likely always try to reach the maximum sampling, so some red will appear there. This is perfectly normal and doesn't slow down the rest of the rendering while ensuring the problematic parts of the image will clean up as per the user's settings.

UI Path: ||Render Setup window|| > Render Elements tab > Add button > VRaySampleRate

 

 

Parameters

This render element is enabled through the Render Elements tab of the Render Setup window in 3ds Max and displays its parameters in a rollout at the bottom of the window:

VRayVFB – When enabled, the render element appears in the V-Ray Virtual Frame Buffer.

Deep output – Specifies whether to include this render element in deep images.

 

 

Common Uses

VRaySampleRate can be used with both the Bucket and Progressive image samplers.

 

Bucket Image Sampler

The Sample Rate Render Element is useful for fine-tuning render settings using a "red is bad" rule.

Below is a scene with minimal red in the Sample Rate Render Element, indicating that the sampler had a high enough Max Subdivs value to hit the desired noise level.

Sampler RGB

Render time = 11m 39s, Max Subdivs = 24, Noise Threshold = 0.01, Min shading rate = 6

The image sampler is mostly able to reach the noise threshold using the subdivisions allotted.

 

 

In the next image, the sampler did not have a high enough Max Subdivs value to hit the desired noise level. The high amount of red shows that the image sampler cut off sampling before the image hit the desired noise level. Noise can be decreased by increasing the Max Subdivs parameter to allow the image sampler to reach the desired noise level.

Sampler RGB

Render time = 6m 17s, Max Subdivs = 8, Noise Threshold = 0.01, Min shading rate = 6The Image sampler is mostly not able to reach the specified noise threshold.

 

 

The primary samples can be allocated to the complex areas of the image by increasing both the Max Subdivs and the Noise Threshold values. This way, V-Ray has enough available primary samples to lower the noise of the complex areas in exchange for an overall slight increase in noise, while still keeping the render times down.

Sampler RGB

Render time = 5m 37s, Max Subdivs = 12, Noise Threshold = 0.02, Min shading rate = 6Sample Rate Render Element with not enough max subdivs.The Image sampler is mostly not able to reach the specified noise threshold.

 

 

Alternatively, the image sampler can allocate primary and secondary samples by changing the Min shading rate value.

For this scene, increasing the Min shading rate allows the sampler more secondary samples to focus on cleaning the lighting, GI, reflections and refractions. In exchange, some of the detailed fur and high contrast areas are a bit noisier as there are not enough primary samples taken for those areas.

Sampler RGB

Render time = 8m 38s, Max Subdivs = 8, Noise Threshold = 0.01, Min shading rate = 20Sample Rate Render Element with not enough Max Subdivs.  Less primary samples are needed to hit the desired noise level, since more secondary samples are taken.

 

Progressive Image Sampler

The Progressive sampler uses the same algorithm as the Bucket sampler. The main difference is that the maximum samples increase as the sampler finishes each pass. 

 

 

11 passesVery few samples are given to complex areas of the image

36 passesSamples start to focus on difficult areas.

200 passesMany samples start to collect only when needed. White areas are the primary target now.