3 Ways To Magnetize Metal - WikiHow
Maybe your like
- Log in / Sign up
- Rubbing the Metal with a Strong Magnet |
- Striking the Metal with a Hammer |
- Making an Electromagnet |
- Video |
- Expert Interview |
- Expert Q&A
This article was co-authored by Himesh Patel. Himesh Patel is a Metallurgical Engineer at Mcclelland Laboratories in Reno, Nevada. With over five years of industry and graduate research experience in the raw materials industry, Himesh has extensive knowledge of mining and mineral extraction and recovery methods, mine financing, and the environmental impacts of mining. He received his MS in Metallurgical Engineering from the University of Nevada, Reno, and a Dual Degree in Mineral Engineering from the Indian Institute of Technology (Indian School of Mines), Dhanbad. Himesh is passionate about educating the public about the minerals industry. There are 7 references cited in this article, which can be found at the bottom of the page. This article has been fact-checked, ensuring the accuracy of any cited facts and confirming the authority of its sources. This article has been viewed 284,799 times.
Magnetism occurs when negative and positive particles in an object line up in a specific manner, causing an attraction or repulsion with nearby particles. As long as a metal has some iron in it, you can magnetize it using another magnetic metal or an electromagnet. While you need a strong magnet to make another metal magnetic, the magnetism produce will probably not be very strong;[1] it will be sufficient to pick up a paperclip or a screw. The strength of the magnet depends upon the iron content.
Steps
Method 1 Method 1 of 3:Rubbing the Metal with a Strong Magnet
-
1 Gather the necessary materials. To magnetize metal with this method, you just need a strong magnet and a piece of metal with known iron content.[2] Metals without iron will not become magnetic. - A strong magnet, such as neodymium, can easily be purchased online.
-
2 Identify the North pole of the magnet. Every magnet has two poles, a North and a South pole. The North pole is the negative side, while the South pole is the positive side. Some magnets have the poles labeled directly on them.[3] - If your magnet is not labeled you can use a pole identifier magnet. This is a magnet that has the poles labeled on it. Place the identifier near your magnet and see which side attaches. Opposite sides attract, so if the magnet attaches to the South pole of the identifier magnet, that side is the North pole.
-
3 Rub the North pole from the middle of the metal to the end. With firm pressure, quickly run the magnet across the piece of metal. The act of rubbing the magnet across the metal helps the iron atoms align in one direction. Repeatedly stroking the metal gives the atoms more opportunity to line up.[4] - Repeat the stroke towards the negative pole at least ten times. Ten strokes is just a good number to start with. You can do more or less as long as the metal works to your satisfaction as a magnet.
-
4 Test the magnetism. Tap the metal against a pile of paperclips or try to stick it to your fridge. If the paperclips stick or it stays on the fridge, the metal has been sufficiently magnetized. If the metal does not become magnetized, keep rubbing the magnet in the same direction across the metal. - If you are magnetizing a screwdriver, put it next to a screw to see if it holds it.
-
5 Continue rubbing the magnet against the object to increase the magnetism. Make sure you rub the magnet in the same direction every time. After ten strokes, check the magnetism again. Repeat until the magnet is strong enough to pick up the paper clips. If you rub in the opposite direction with the North pole this will actually demagnetize the metal. - If the metal still does not maintain magnetization, it might not have a high enough iron content. Try this method again with a metal that has a higher iron content.
Advertisement
Striking the Metal with a Hammer
-
1 Gather the necessary materials. To magnetize a metal using a hammer, you will need a compass, a hammer, and a piece of metal with some iron. These items can easily be purchased at a local hardware store.[5] - A metal alloy that doesn’t have iron in it is less likely to be magnetic. Pure gold, silver, copper, etc. cannot be magnetized with this method.
-
2 Identify north with the compass. A compass works because of the magnetic poles of the Earth. There is a small magnetized needle in the compass that always faces north due to the poles. Place your compass flat on the table and let the needle swing until it stops moving. The direction the needle points towards is north. -
3 Position the piece of metal facing north.[6] Place the piece of metal on a table and orient it so that it is pointing in the same direction as the needle of the compass (north). The piece of metal needs to be facing north so that the iron atoms will align along the magnetic pole of the Earth.[7] - Secure the piece of metal to the tabletop using tape or a clamp such as a vice.
-
4 Hit the end of the metal with the hammer. With the metal securely in place, strike the bottom end (end facing south) of the piece with the hammer.[8] Striking the metal allows the iron atoms to move around and align themselves in the direction of the Earth’s magnetic field. - Hit the end multiple times to increase the magnetism of the metal.
-
5 Test the magnetism of the metal. Place the piece of metal on top of some paper clips and see if they stick. If the paper clips stick, the metal has been magnetized. If the paperclips don’t stick, try striking the end of the metal a few more times.[9] - If you find this method doesn’t work, the amount of iron in the piece of metal might be too small. Try it with another piece of metal that you know has more iron in it.
Advertisement
Making an Electromagnet
-
1 Gather the necessary materials. To make an electromagnet, you will need insulated copper wire, a piece of metal with known iron content, a 12-volt battery (or other DC power supply), wire strippers/cutters, and electrical tape.[10] - The insulated copper wire needs to be thin enough to easily wrap around the metal and long enough to wrap a few dozen times.
- Make sure the metal has no magnetization before beginning.
- Using an AC power source will also work, but is not recommended because it is high voltage and there is potential for an electric shock.
-
2 Wrap the insulated wire around the piece of metal. Take the wire and leaving a tail of about an inch, tightly wrap the wire around the metal a few dozen times. The more times you wrap the coil, the stronger the magnet will be. Leave a tail at the other end of the wire as well. - At this point, you should have two wires dangling off either end of the metal, with the wire coiled tightly around it.
-
3 Strip the ends of the copper wire. Using the wire strippers, strip off at least ¼ inch up to ½ inch from both ends of the wire. The copper needs to be exposed so that it can come into contact with the power source and provide electricity to the system. - Take care not to cut through the wire when stripping it.
-
4 Connect the wires to the battery. Take one bare end of wire and wrap it around the negative terminal of the battery. Using electrical tape, secure it in place and make sure the metal of the wire is touching the wire of the terminal. With the other wire, wrap and secure it around the positive terminal of the battery.[11] - It doesn’t matter which wire is connected to which terminal as long as both are securely attached to separate ones.
-
5 Test the magnetism. When the battery is properly connected it will provide an electrical current that causes the iron atoms to aligned creating magnetic poles. This leads to the metal becoming magnetized. Tap the metal against some paperclips and see if it can pick them up.[12] - Some metals will remain magnetized when the battery is removed, while others, such as “soft iron” require the electric current for the magnetization.
Advertisement
Expert Q&A
Search Add New Question- Question What are 5 metals that are not magnetic?
Himesh Patel Metallurgical Engineer & Manager Himesh Patel is a Metallurgical Engineer at Mcclelland Laboratories in Reno, Nevada. With over five years of industry and graduate research experience in the raw materials industry, Himesh has extensive knowledge of mining and mineral extraction and recovery methods, mine financing, and the environmental impacts of mining. He received his MS in Metallurgical Engineering from the University of Nevada, Reno, and a Dual Degree in Mineral Engineering from the Indian Institute of Technology (Indian School of Mines), Dhanbad. Himesh is passionate about educating the public about the minerals industry.
Himesh Patel Metallurgical Engineer & Manager Expert Answer Some common metals that aren't magnetic include aluminum, copper, brass, gold, silver, tin, tungsten, and lead. Thanks! We're glad this was helpful. Thank you for your feedback. If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow Yes No Not Helpful 1 Helpful 9 - Question How do real magnets get magnetized?
Community Answer When two magnets are close together, their magnetic field lines cut through each other creating magnetization. Thanks! We're glad this was helpful. Thank you for your feedback. If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow Yes No Not Helpful 29 Helpful 18 - Question Why do I have to magnetize with the north end of the magnet? As long as I don't keep swapping ends, shouldn't it work either way?
Andrew Geep Community Answer You are absolutely right. There is no difference which end you use. One end is south and the other is north. The center is neutral, that is, it is not magnetic and will not attract anything. By the way, did you know that if you cut a bar magnet in two you will have two magnets? The part of the magnet that had the south end will be south and the part that used to be neutral is now the new north. The same principle applies to the other end. Each "new" magnet will have half the strength of the original. Thanks! We're glad this was helpful. Thank you for your feedback. If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow Yes No Not Helpful 5 Helpful 32
Video
Tips
Submit a Tip All tip submissions are carefully reviewed before being published Name Please provide your name and last initial Submit Thanks for submitting a tip for review!You Might Also Like
Expert Interview
Thanks for reading our article! If you’d like to learn more about magnetizing, check out our in-depth interview with Himesh Patel.
References
- ↑ Himesh Patel. Metallurgical Engineer & Manager. Expert Interview
- ↑ Himesh Patel. Metallurgical Engineer & Manager. Expert Interview
- ↑ https://ece.northeastern.edu/fac-ece/nian/mom/work.html
- ↑ https://commons.princeton.edu/josephhenry/permanent-magnet/
- ↑ https://sciencing.com/make-super-strong-permanent-magnets-6520830.html
- ↑ https://commons.princeton.edu/josephhenry/permanent-magnet/
- ↑ https://van.physics.illinois.edu/ask/listing/436
- ↑ https://commons.princeton.edu/josephhenry/permanent-magnet/
- ↑ https://sciencing.com/make-super-strong-permanent-magnets-6520830.html
- ↑ https://www.teachengineering.org/activities/view/cub_mag_lesson2_activity1
- ↑ https://www.teachengineering.org/activities/view/cub_mag_lesson2_activity1
- ↑ https://www.sciencelearn.org.nz/resources/2564-making-an-electromagnet
About This Article
To magnetize metal, like a screwdriver for instance, you’ll need a strong magnet. Start by identifying the North pole of the magnet, which should be labeled directly on the magnet. Then, stroke the north end of the magnet against the metal about a dozen times in the same direction to create a magnetic charge. Try to pick up some nails to see if it worked. If not, repeat the process, or try magnetizing a different metal with a higher iron content. Keep reading to learn how to make an electromagnet! Did this summary help you?YesNo
In other languages Spanish Russian Italian German French Japanese- Send fan mail to authors
Reader Success Stories
-
Kristi Brown
Jan 24, 2017
"I remembered learning, as a child how to make a magnet by rubbing a piece of metal with a magnet. However, I couldn't remember the all the details. I found this tutorial and I knew it was just what I had learned. Just for fun, I tried it, and it worked!"..." more
Did this article help you?
Yes No Advertisement Cookies make wikiHow better. By continuing to use our site, you agree to our cookie policy.Kristi Brown
Jan 24, 2017
"I remembered learning, as a child how to make a magnet by rubbing a piece of metal with a magnet. However, I couldn't remember the all the details. I found this tutorial and I knew it was just what I had learned. Just for fun, I tried it, and it worked!"..." moreJames Paz
Mar 21, 2017
"I was doing Physics homework, and the strategy helped a lot." Rated this article:Etoma Geofrey
Jan 4, 2017
"I am so delighted by this site, bravo!"Anonymous
May 4, 2017
"It helped with my science fair!"Anonymous
May 5, 2016
"Pretty good. Hope it lasts." Share yours! More success stories Hide success storiesQuizzes & Games
You Might Also Like
Featured Articles
Trending Articles
Featured Articles
Featured Articles
Watch Articles
Trending Articles
Quizzes & Games
- Categories
- Education and Communications
- Studying
- Science
- Home
- About wikiHow
- Experts
- Jobs
- Contact Us
- Site Map
- Terms of Use
- Privacy Policy
- Do Not Sell or Share My Info
- Not Selling Info
- Contribute
Follow Us
×Get all the best how-tos!
Sign up for wikiHow's weekly email newsletter
Subscribe You're all set! X --Tag » How Can You Magnetize A Material
-
List Four Methods Of Magnetizing A Magnetic Substance. - Toppr
-
Magnetizing And Unmagnetizing - MagLab
-
How To Magnetize Things - Sciencing
-
How Materials Are Magnetized And Demagnetized?
-
IGCSE Physics - Unit 4 Electricity And Magnetism
-
Magnetization Methods And Characteristics
-
4 Methods Of Magnetizing Components And Materials For Magnetic ...
-
Methods Of Magnetisation And Demagnetisation - YouTube
-
Magnets & Magnetism Frequently Asked Questions
-
Permanent Magnet – Joseph Henry Project - McGraw Commons
-
Magnetism | National Geographic Society
-
Magnetic Materials - What Materials Make Magnets | First4Magnets
-
Researchers Propose A Method Of Magnetizing A - EurekAlert!
-
Magnetization - Wikipedia