How To Replace A Wick In A Kerosene Heater | EHow

Share

1. Home Sweet Home
2. Home Maintenance & Repairs

How to Replace a Wick in a Kerosene Heater By Helen Jain eHow may earn compensation through affiliate links in this story. Learn more about our affiliate and product review process here.

Things You'll Need

• Screwdriver

• Marker

Kerosene is often used in heaters and lamps.

Kerosene heaters use a wick that is lowered and rises for added or lowered heat contents. The wick soaks up the kerosene oil so that the top of the wick is covered in oil and draws up the kerosene until the entire heater no longer has oil. Replacing the wick is a necessary part of maintaining the heater and avoiding problems with the heater. Wick replacement is necessary about once a year to prevent problems with the kerosene heater.

Advertisement

Step 1

Burn out the kerosene oil until it is completely dry and drained. Allow the unit to cool before touching it.

Video of the Day

Step 2

Remove the batteries, adjusting knob and fuel tank. These usually are pulled out without difficulty.

Advertisement

Related Stories

Home Sweet Home How Do I Disassemble a Moen 103258 Faucet? Home Sweet Home How to Replace a Humidifier Filter on a Furnace Home Sweet Home How to Calculate Tension Underwater

Step 3

Remove the catalytic converter. Open the grill to get this out and lift it out. Avoid accidentally breaking the glass chimney.

Step 4

Unscrew the cabinet and remove it. Lift it out and place it beside the screws to avoid losing the screws. Remove the windshield if the heater has a windshield. The windshield sits over the burner.

Advertisement

Step 5

Unscrew the wing nuts at the base of the heater. Lift the wick adjuster straight up to remove it from the base of the heater.

Step 6

Mark the old wick at the base of where it sticks out and then remove it from the holder sleeve by folding it inward. Remove the wick from the holding teeth. Be careful of the teeth because they are very sharp and can hurt.

Advertisement

Step 7

Compare the marked line on the old wick to the black line found on the new wick. Mark the new wick if the lines do not match up so that they will. This determines how far to insert the replacement wick.

Step 8

Fold the new wick and place it into the holder sleeve until the mark shows the area to stop. Press the wick into the holding teeth to keep it in place.

Advertisement

Step 9

Slide the new wick and the sleeve into the draft tube. Rotate and press hard so that the teeth catch the wick firmly. Check that the sleeve moves freely in the draft tube and that it is at the center.

Step 10

Look at the gasket and make sure it is on top of the fuel tank. Check that the wick adjuster shaft is toward the front.

Advertisement

Step 11

Place the adjuster knob back onto the unit. Check for tension or problems with adjusting. Adjust until lowered completely. Rotate the knob 3/4 of a turn in a clockwise direction, and then insert the pinion. Lower the unit onto the base and check it for ease of movement. Loosely screw on the wing nuts. Move the wick until it is fully upright.

Advertisement

Step 12

Tighten the wing nuts and check the wick height. Make sure it is even all the way around and that it is around 3/8 of an inch in height. If adjustments are needed, loosen the wing nuts and adjust the wick before tightening again.

Step 13

Remove the adjusting knob and then put the heater back together in the opposite direction as it was taken apart. Do not burn the heater until the wick has soaked up oil, usually around 20 to 60 minutes depending on the heater.

Advertisement

Video of the Day

references

• End Times Report: Kerosene Heater Wick Replacement
• Kerosene Wicks: FAQs
• Miles Stair’s Wick Shop: Troubleshooting Kerosene Heaters

eHow may earn compensation through affiliate links in this story. Learn more about our affiliate and product review process here.

you may like

1

The American Standard Plebe Toilet Won't Stop Running

2

How Do I Repair a 1500 Delta Series Faucet?

3

How to Fix a Small Hole in a Water Heater

You May Also Like

1

How To Repair a Delta Single Lever Waterfall Faucet Spout

2

How to Replace the Chain on a Husqvarna 455

3

How to Replace a Fuse in a Hager Fuse Box