| Top  WICKS TO FIT THE HEATERS LISTED BELOW - AND MORE! - ALADDIN
- ALLIED
- ALOHA
- ALPACA
- AMERICANA
- AMERICAN WICK
- ARTIFEX
- A.P.I ARTURO
- AUSTRALIA - ALL HEATERS
- AVANTI
- BANDO
- BARLER, Nesco
- BASIC
- BEATRICE
- BOMBARDIER
- BOSS
- Bunsen
- BUTTERFLY
- CANDLE
- CHEVRON
- CITATION
- CODEP
- COMFORT GLOW
- COMFORTEMP
- COMFORTOR
- COMMANDER
- CORONA
- COSY
- CRESTLINE
- DANRICH
- DESIGN HOUSE
- DIXIE
- DURA-HEAT
- DYNA GLO
- DYNA GLOW
- EASY
- EGAWA
- EMERSON
- ENERGY MART
- ENERGY MISER
- ENERGY STAR
- ENVIROTEMP
- EVERGLOW
- EUROSTOVE and European heaters
- EVERSPLENDOR
- FANCO
- FLAMEGLO
- FUJIKA
- FUJISUN
- FUTURA
- GEMINI III
- GENERAL
- GERALD
- GLO
- GOLD STAR
- GOLDEN GLO
- HALLER
- HALLMARK
- HAMAI
- HANDY MASTER
- HANSON
- HART
- HARTLEY-RAND Handy Hearth
- HEAT BUSTER
- HEAT-GLO
- HEAT MATE
- HEAT-MOR
- HENRY ISLAND
- HIKARI
- HITACHI
- HUSKY
- IMARFLEX
- INTERNATIONAL
- KAI (Kupanoff)
- KENROY
- KERO HEAT
- KERO JET
- KERO KNIGHT
- KERONA
- KERO SOLAR
- KERO SUN
- KERO-TECH
- KEROTEMP
- KEROWORLD
- KERRAY
- KETAC
- KEYMAR
- KNAPP MONARCH
- KOEHRING
- KOGY and KOZY
- KUPANOFF
- LEO PET
- LESLIE LOCKE
- LITWIN
- LOUDI
- MAGNUM
- MAXIM
- MEDALLION
- MEGA
- MITAKA
- MULTIPLEX
- NATIONAL
- N.E.C.
- NISSEI
- NOBLE
- NORTHERN
- NORTH STAR
- NORTHERN ELECTRIC
- NORTHERN LIGHT
- NOVA
- PACICO
- PANASONIC
- PERFECTION
- PDQ
- POD
- PORTA HEAT
- PREMIER Heaters
- PREMIER STOVES
- PROSPERITY II
- R.M.C (Dyna Glo)
- RADIANT KING
- RELYAN
- RIPPENGILLES
- ROBESON
- RUBY
- SAGA
- SAM-HWA
- SAMARITAN
- SANYEI
- SANYO
- SEARS
- SENGOKU
- SHARP
- SHETLAND
- STA-GLO
- SUN AIR GLO
- SUNBEAM
- SUNCREST
- SUN HOUSEWARES
- SUNNY
- SUNNY-VOX
- SUNSHINE
- SUNSTAR
- SUNWISE
- SWASTIK STOVES
- Swiss Tent Heater
- TAKO
- TATUNG
- TAYOSAN
- TEKNIKA
- Titan Industries
- TOSHIBA
- TOUCH ‘N GLOW
- TOYOKUNI
- TOYOSTOVE
- TOYOTOMI
- TOYOSET
- TURCO
- Turm L51
- "21ST CENTURY"
- UNION
- US Stove Co.
- UNITED AMERICA HARDWARE
- VALOR
- VAN WICK
- VORTEC FTTA LTD.
- WAL MART
- WARM MATE
- WARM-UP SQUAD
- WESTERN AUTO
- WHITE GATE
- YEIH TUNG
- YUASA
- ZIBRO - KAMIN and other European heaters also OZ and NZ
Unique Specialty wicks for 19th Century lamps |   . . World's Largest Selection of Wicks! Wicks for virtually every heater, stove and lamp made since 1850 KEROSENE HEATER WICK REPLACEMENT GENERIC INSTRUCTIONS FOR UNPINNED WICKS Instructions for wick replacement are packaged with the replacement wick. There are, however, a lot of older heaters to be found with spare wicks but no clue as to how to install new wicks. Because most of the older heaters use an unpinned wick, and many of them are radiant heaters, what follows could be considered as generic instructions. Details will vary; some cabinets are attached to the base in different ways, the wick adjuster assembly will look a little different, etc. But the basic design philosophy must remain the same - there is a wick, it must be raised and lowered, the usual method of wick movement is via a gear shaft and turning knob, etc. These instructions are simply give you a clue to what to look for as you disassemble your heater to replace the wick. The illustrations are thumbnails: click on the illustration to see a full size image, then use the "back" button on your browser to return to this page. | 
| First, burn the heater "dry" to have a dry wick and sump, then make sure your stove is cool! Remove the fuel tank, the batteries (usually in the back), and all the knobs and levers in the front panel which are too wide to fit the slot in the cabinet. Open the grill and remove the catalytic converter, then set it carefully away from your work area so it won't be hit or tipped over and break the glass chimney. | | 
| Unscrew the retaining screws that hold the cabinet to the base of the heater. They can be plastic knurled knobs or Phillips screws, usually one on each side and one in the back. Lift the cabinet toward the front to clear the lever shafts, and remove it from the base. | | 
| If there is a wind shield, remove it. If the ignition unit is fastened to the assembly, carefully remove it (2 screws) and set aside on the base. Finally, unscrew the wing nuts (usually 4) holding the wick adjuster assembly to the base. Now the entire wick adjuster assembly can be removed by lifting it straight up. | |  | Mark the wick to be removed at the top edge with a laundry market, right around the wick using the sleeve as a guide. Remove the wick from the inner wick holder sleeve by folding it inward. Free it from the sharp teeth that keep it in place, then slide it out. Remember, those teeth are VERY SHARP! | |  | The replacement wick should have a black line around it. Compare that line with the one you drew on the old wick to be sure it is the same height from the top. If it doesn't, draw a new line. Fold the wick, then insert it into the sleeve, with the black line just above the top of the sleeve, then press it smooth and into the sharp teeth to keep it in place. | |  | Slide the wick and sleeve back onto the draft tube. Rotate around and press hard against the draft tube to fully insert the sharp teeth into the wick. Make sure the wick slides freely around the draft tube in the center! Make sure the gasket is in place on the top of the fuel tank - the gasket that fits between the wick adjuster assembly and the tank. The wick adjuster shaft should be toward the front. | | 
| Put the wick adjuster knob back on the shaft. Check to see if the spring tension of the adjuster assembly is free of tension. Move the manual shut off or tip-over switch so it lowers all the way. Rotate the knob about 3/4 turn clockwise, then hold the latch in that position. Insert the pinion on the inside of the wick raising shaft, with the wick holder slot with teeth near the top. Lower the unit onto the base, then make sure the wick will raise and lower easily, and there is spring tension on the shaft. Put the wing nuts back loose, then move the wick all the way up. | | 
| Tighten the wing nuts, then check the height of the wick. There should be about 3/8" (5/16" min, 7/16" max) of wick showing, and the gap between the wick holder and draft tube should be uniform all around. Use the base of a 5/32" or 3/16" drill bit as a gauge. Loosen the wing nuts and adjust if necessary. Then remove the wick adjuster knob. | Congratulations! You have installed a new wick in your kerosene heater. Now all that is left to do is to find all the screws you took out during assembly, and reassemble the heater. First the electric igniter is replaced, then the wind shield (if any) is installed, and the base of the unit is ready for the cabinet. Lower the cabinet GENTLY over the base, with the top tilted toward you (the front), and settle it down onto the base. Look around the base of the unit: sometimes there will be tabs for the base screws, and you need to make sure those tabs are on the INSIDE of the cabinet - not showing! Now the screws can be reinstalled to hold the cabinet to the base. Next, put the wick raising knob back on - plus any other knobs you may have had to remove. At this point, stop everything and try out the wick raising assembly and the safety tip-over switch. Check to be sure the wick raises the proper amount (about 5/16" to no more than 1/2"), then shut off the heater to make sure the wick retracts by spring tension down inside the wick tube - that is your safety device! Make sure the igniter moves into the wick and glows. Everything work? Great. Now you can open the grill and replace the catalytic converter. Put the fuel tank back into the cabinet - full of fuel up to half way on the sight level - and sit back and admire your work. DO NOT attempt to light the heater for at least 20 minutes, as the wick you installed is completely dry and needs to suck up fuel via capillary action before you can light the heater! A half hour up? Now you can test your handiwork. Light the heater and wait for it to heat up completely. If you have installed the wick to a uniform height all around, the flame will be uniform. If one edge of the flame is too high, you can trim the wick a little lower at that spot when the heater is cool. If half of one side of the flame is considerably higher than the other, you will need to reinstall the wick again, making sure that side is installed lower. Notice that the flame is a little too high? That is because you are burning a brand new wick that has no carbon build-up on the top surface. In a week that problem will be solved. In the meantime, burn the heater with the wick turned to the lowest setting, and the wick height should be ideal. After a week or so of use and burning dry once or twice, the wick will be all "settled in" and maintain that capillary action for a whole season, so you won't need to take the heater apart and raise the wick for a whole season of use, and the highest setting on your control knob should have the flame at precisely the right height for efficient, clean, odor free burning for a long time. You did it! These generic instructions also apply to convection heaters - only the cabinet is different. With a convection heater, the tower is removed with 3 or 4 thumb screws at the base of the tower, lift it straight up and off, and the wick adjuster assembly is essentially the same as with a radiant heater. Back to top of page | Home Page Site Index Kerosene Heater Wicks: Alphabetical list of most kerosene heaters and the proper wick, & cart checkout. List by wick number and the heaters that fit them. (A helpful guide for buying on eBay) Measurements needed if you have an unlisted heater Care & Maintenance of Kerosene Heater Wicks - Installing Kerosene Heater Wicks - generic for unpinned wicks
Installing Perfection 500 Heater Wicks PINNED OR UNPINNED WICK? PHOTOS OF BOTH TYPES Kerosene Heaters -
Kerosene Heaters - General types, how they work, recommendations for some good ones - and those I would avoid. -
Economic Benefits of Kerosene Heaters -
Kerosene Heater Safety -
Regular maintenance -
Troubleshooting kerosene heater common problems -
Breaking In New Kerosene Appliances -
Burning Kerosene Heaters at Night -
Flame Spreader Heaters and Lamps - A Century of Excellence -
Kerosene Heater Carts - why carry your heater around? -
Kerosene Fuel Primer -
Sweet Smelling Kerosene -
Kerosene tank cradles (photo) Building a Cradle -
HALLER "ORIGINEEL" STOVES -
KEROSENE HEATERS MADE IN THE NETHERLANDS -
Beatrice Boiling Stoves & Mini kerosene heaters you can make -
Sad Iron stoves; Wicks & Installation instructions -
Wicking For Oil Burning "WICKLESS" Stoves & Ranges Lamps -
Center Draft Lamp wicks -
Flat & Kosmos lamp wicks -
Center Draft Lamp Chimneys -
"Sans Rival" borosilicate chimney for 14''' Kosmos lamps New! -
Student Lamp Sans Rival Chimney with 1 7/8" fitter!!! -
Center Draft Kerosene Lamps (Photos, info and history) -
Photos of restored center draft lamps. -
Care, Feeding and Restoration of Center Draft Lamps (and wick installation for many) -
Center Draft Lamp manufacturers and brand names -
Lamp Chimneys - Dimension of nominal base diameter by make, model and "line". -
Early American Metal Font & Specialty Lamps -
Aladdin Lamp History - Aladdin Lamp Wicks & Chimneys, Exploded burner views. -
Kosmos-Brenner lamps and wicks -
"Sans Rival" borosilicate chimney for 14''' Kosmos lamps New! -
Flame Spreaders and "Smoke Consumers" from Alex Marrack-
Articles by Alex Marrack: -
Centre Draught Oil Lamps English and European Models -
The L&B Lamp Belge or Belgian Lampe Home Page Site Index Photo Album Photos of Wicks Mail Order Form Back to top of page Kerosene Stoves, Lanterns and Ovens Kerosene Stoves - Recommendations on different models New! Kerosene Stove Maintenance and Storage Butterfly A-822, 22 wick, all-aluminum premium stove. New! Butterfly #2487, 16 wick stove. Butterfly #2412 Pressure Stove; instructions for virtually any pressure stove. Butterfly #2418 Double Burner Stove; good with any gravity flow stove. Butterfly #2421 Oven for Kerosene Stoves Butterfly #2641, 10 Wick Stove - the least expensive emergency stove. Butterfly #2698 Cook Stove - THE Best Heavy Duty Cook Stove. Butterfly #828R Pressure Lantern; same for most pressure lanterns. |