KY-026: Flame Sensor - Tkkrlab Arduino Cursus

TkkrlabArduino cursus

• Home

• Les 1: Looplicht
  • Looplicht zonder delay
• Les 2: Seriële poort
• Les 3: Servo motor
• Les 4: Relais
• Les 5: LCD scherm
• Les 6: Domotica met de nodeMCU
  • CH340 driver installatie
  • Het NodeMCU bord
  • MQTT
  • Athom Homey
    • Automatische plantenbak
    • DHT11 sensor
    • NFC
    • Simon says
• Les 7: Arduino datashield
• Cursus: datalogger
• Basiskennis elektronica
• Arduino kit
• Sensoren
  • KY-001: Temperature sensor
  • KY-002: Vibration switch
  • KY-003: Hall magnetic sensor
  • KY-004: Key switch
  • KY-005: Infrared emission sensor
  • KY-006 Small passive buzzer
  • KY-008 Laser sensor
  • KY-009: RGB LED SMD
  • KY-010: Optical broken module
  • KY-011: 2-color LED module
  • KY-013: Analog Temperature sensor
  • KY-015: Digital temp & humidity
  • KY-016: 3 color LED
  • KY-017: Mercury open optical
  • KY-018: Photoresistor module
  • KY-019: 5V Relay
  • KY-020: Tilt switch
  • KY-021 : Mini magnetic reed
  • KY-022 : Infrared sensor receiver
  • KY-023: XY-axis joystick
  • KY-024: Linear magnetic Hall
  • KY-025: Reed module
  • KY-026: Flame sensor
  • KY-027: Magic light cup
  • KY-028: Reed module
  • KY-029: Yin Yi 2 color LED
  • KY-031: Knock sensor
  • KY-032: Obstacle avoidance
  • KY-033: Analog Hall magnetic
  • KY-034: 7 color flashing LED
  • KY-035: Reed module
  • KY-036: Metal touch sensor
  • KY-037: Sensitive microphone
  • KY-038: Microphone sound sensor
  • KY-039: Detect the heartbeat
  • KY-040: Rotary encoder
• Tips
• Appendix

More

• Wiki
• Tkkrlab website

Built with from Grav and Hugo

Tkkrlab Arduino cursus > Sensoren > KY-026: Flame sensor

• KEYES ARDUINO Flame module
• Schematic
• Example Code

KY-026: Flame sensor

Buy sensor or kit.

KEYES ARDUINO Flame module

Flame module Interface module and number 13 comes with LED build a simple circuit to produce flame warning lamp 13 comes with digital interfaces of the LED, the flame sensor connected digital three interfaces, when the flame sensor senses There are key signal detected, LED lights, otherwise off.

Sensor for flame wavelengths between 760 nm to 1100 nm infrared is most sensitive 60 degree detection sensor Two outputs mode:

• AO: analog output- real-time output voltage signal on the thermal resistance
• DO: when the temperature reaches a certain threshold- the output high and low signal threshold adjustable via potentiometer

Schematic

• Arduino GND –> Module G
• Arduino +5V –> Module +
• Arduino digital 4 –> Module D0
• Arduino A3 –> Module A0

Example Code

//Example for KY-026 //TkkrLab int Led = 13 ;// define LED Interface int buttonpin = 3; // define the flame sensor interface int analoog = A3; // define the flame sensor interface int val ;// define numeric variables val float sensor; //read analoog value void setup () { pinMode (Led, OUTPUT) ;// define LED as output interface pinMode (buttonpin, INPUT) ;// output interface defines the flame sensor pinMode (analoog, INPUT) ;// output interface defines the flame sensor Serial.begin(9600); } void loop () { sensor = analogRead(analoog); Serial.println(sensor); // display tempature val = digitalRead (buttonpin) ;// digital interface will be assigned a value of 3 to read val if (val == HIGH) // When the flame sensor detects a signal, LED flashes { digitalWrite (Led, HIGH); } else { digitalWrite (Led, LOW); } delay(1000); }