Toyota 4Runner: Open In ABS Solenoid Relay Circuit (C0278,C0279)

Toyota 4Runner: Open in ABS Solenoid Relay Circuit (C0278,C0279) Toyota 4Runner Service Manual / Brake / Brake Control / Dynamic Control Systems / Vehicle Stability Control System(for Hydraulic Brake Booster) / Open in ABS Solenoid Relay Circuit (C0278,C0279)

DESCRIPTION

The solenoid relay is built into the master cylinder solenoid.

This relay supplies power to each solenoid. If the initial check is OK, after the ignition switch is turned to ON, the relay turns on.

DTC Code	DTC Detection Condition	Trouble Area
C0278	Either condition is met: Both of the following conditions continue for at least 0.2 seconds. IG voltage is between 9.5 and 17 V. The relay contact is open when the relay is on. Both of the following conditions continue for at least 0.2 seconds. IG voltage is 9.5 V or less when the relay is on. The relay contact remains open.	ABS NO. 2 fuse Solenoid relay circuit Master cylinder solenoid
C0279	The following condition continues for at least 0.2 seconds. The relay contact is closed immediately after turning the ignition switch to ON when the relay is off.

WIRING DIAGRAM

Refer to DTCs C0226, C0236, C0246, C0256, C1225, C1226, C1227 and C1228 (See page ).

CAUTION / NOTICE / HINT

NOTICE:

• When replacing the master cylinder solenoid, perform calibration (See page ).
• Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE

1.	CHECK TERMINAL VOLTAGE (+BS)

(a) Disconnect the A6 skid control ECU connector.

(b) Measure the voltage according to the value(s) in the table below. Standard Voltage: Tester Connection Condition Specified Condition A6-31 (+BS) - Body ground Always 11 to 14 V Text in Illustration *a Front view of wire harness connector (to Skid Control ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

2.	CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL)

(a) Disconnect the A6 and A7 skid control ECU connectors.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
A6-1 (GND1) - Body ground	Always	Below 1 Ω
A6-32 (GND2) - Body ground	Always	Below 1 Ω
A7-4 (GND3) - Body ground	Always	Below 1 Ω

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

3.	RECONFIRM DTC

HINT:

These codes are stored when a problem is detected in the master cylinder solenoid.

The solenoid relay is in the master cylinder solenoid.

Therefore, solenoid relay circuit inspections and relay unit inspections cannot be performed. Be sure to check if any DTC is output before replacing the master cylinder solenoid.

(a) Clear the DTCs (See page ).

(b) Drive the vehicle at a speed of approximately 32 km/h (20 mph) or more for 60 seconds or more.

(c) Check if the same DTCs are output (See page ).

HINT:

Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.

Result

Result	Proceed to
DTC is output	A
DTC is not output	B

A

REPLACE MASTER CYLINDER SOLENOID

B

USE SIMULATION METHOD TO CHECK

SFR Solenoid Circuit (C0226,C0236,C0246,C0256,C1225-C1228)

DESCRIPTION The solenoid turns on when signals are received from the skid control ECU and controls the pressure acting on the wheel cylinders, thus controlling braking force. DTC Code ...

ECM Communication Circuit Malfunction (C1203)

DESCRIPTION The circuit is used to send control information from the skid control ECU to the ECM, and engine control information from the ECM to the skid control ECU via the CAN communication sys ...

Other materials about Toyota 4Runner:

Door Control Transmitter(w/ Smart Key System) Components COMPONENTS ILLUSTRATION Removal REMOVAL CAUTION / NOTICE / HINT NOTICE: Take extra care when handling these precision electronic components. PROCEDURE 1. REMOVE TRANSMITTER BATTERY (a) Push the release hook knob and extrac ...

Dtc Check / Clear DTC CHECK / CLEAR 1. CHECK DTC (a) Connect the Techstream to the DLC3. (b) Turn the engine switch on (IG). (c) Turn the Techstream on. (d) Enter the following menus: Body Electrical / (desired system) / DTC. (e) Read the DTCs. 2. CLEAR DTC (a) Connect ...